LC-52XS1E/RU/LC-65XS1E/RU
5 – 14
19.IC7002 (RH-iXC331WJQZQ)
This is a monitor microprocessor, which receives the remote control light, controls the CEC signal, detects the keys, and detects the OPC. It also
detects the errors relating to the power supply within the IF PWB and controls the power supply of the monitor.
20.IC7006 (VHiBR24L04F-1Y)
This is an EEPROM, in which the portion of the data processed by IC7002 is stored.
21.IC5802 (VHi-1Y)
This is a power supply IC, which supplies 5V for the optional wireless transmission unit. It also detects short circuits and has the thermal shutdown
function.
22.IC5901 (VHiBD9045FV-1Y)
This is a DC/DC converter, which inputs 15V from the power supply unit and generates 5V and 3.3V used within the IF PWB.
2ch DC/DC Converter
27
MODE2
I
Distribution, DDR function enable.
The use of these multi-function depends on the setting of MODE<1:0>.
MODE<1:0>=HH(Single-in/Single-out Mode)
H: Distribution function enable.
L: Distribution function disable.
MODE<1:0>=HL(Single-in/Single-out Mode)
H: DDR (Double Edge input) function enable.
L: DDR (Double Edge input) function disable.
30
/PDWN
I
H: Normal operation,
L: Power down (all outputs are Hi-Z)
31
PRBS
I
PRBS generator is active when MODE <1:0> = LL (Dual-in/Dual-out mode)
H: PRBS generator is enable. Pattern is PRBS-23.
L: Normal Operation
10, 11, 12, 16,
28, 32
Reserved
I
Must be tied to GND.
23
Reserved
I
Must be Open.
29, 33, 109
N/C
Must be Open.
3, 13, 82, 93,
104, 113, 125,
137
VCC
-
Power Supply Pins for TTL inputs, output and digital circuitry.
4, 14, 83, 94,
105, 114, 126,
138
GND
-
Ground Pins for TTL inputs, outputs and digital circuitry.
43, 49, 55, 61,
67
LVCC
-
Power Supply Pins for LVDS Outputs.
37, 42, 48, 54,
60, 66, 72
LGND
-
Ground Pins for LVDS Outputs.
35, 74
PVCC
-
Power Supply for PLL circuitry.
34, 36, 73, 75
PGND
-
Ground Pin for PLL circuitry.
Pin No.
Pin Name
I/O
Pin Function
1
OUTL2
O
Low side FET gate drive terminal 2
2
DGND2
-
Low side FET source terminal 2
3
SW2
I
High side FET source terminal 2
4
OUTH2
O
High side FET gate drive terminal 2
5
BOOT2
-
OUTH2 driver power supply terminal
6
CL2
I
Over-current detection setting terminal 2
7
N.C.
-
No Connection
8
VREG5
-
The REG output for FET drive
9
CL1
I
Over-current detection setting terminal 1
10
BOOT1
-
OUTH1 driver power supply terminal
11
OUTH1
O
High Side FET gate drive terminal 1
12
SW1
I
High Side FET source terminal 1
13
DGND1
-
Low side FET source terminal 1
14
OUTL1
O
Low side FET gate drive terminal 1
15
GND
-
Ground terminal
16
TM1
-
Output 1 OCP and an OVP timer latch setting terminal
17
SS1
-
Soft starting time setting terminal 1
Pin No.
Pin Name
I/O
Pin Function
