background image

3

KB-6024MS

KB-6024MK

KB-6024MW

WARNING : The oven should be fully assembled before following procedure.
()  Place one cup of water in the center of the tray in the oven cavity.
(2)  Close the drawer, touch the Defrost pad. Then select Steaks/Chops by touching the number pad 

2. And touch the number pad 5. (Now, weight 0.5lb is set.) And then touch the start pad.

(3)  The oven is in Defrost cooking condition.
(4)  The oven will operate as follows

WEIGHT 

ST STAGE 

2ND STAGE 

3RD. STAGE 

LEVEL 

TIME 

LEVEL 

TIME  LEVEL  TIME 

 

 

0.5lb 

60% 

20sec. 

40% 

20sec. 

30% 

45sec.   

 

(5) If improper operation is indicated, the control unit is probably defective and should be checked. 

 

DEFROST TEST

 

PROCEDURES TO BE TAKEN WHEN THE FUSE ON THE PRINTED WIRING BOARD (PWB) IS OPEN.

2. Re-install the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is installed.
4. Run the oven and check all function.

To  protect  the  electronic  circuits,  this  model  is  provided  with  a  fuse  added  to  the  primary  on  the 
PWB. 
.  Fuse check and repairs.

)  Disconnect the power supply cord.

2)  Remove the outer case cabinet.

3)  Open the door and block it open.
4)  Discharge high voltage capacitor.
5)  If the Fuse is blown, replace power unit.
6)  Make a visual inspection of the varistor. Check for burned damage. If the varistor has been 

burned, replace the power unit.

7)  Examine the touch control transformer with a tester for the presence of layer short-circuit (check 

the primary coil resistance which is approximately 5.6

 ± 0%). If any abnormal condition is 

detected, replace the touch control transformer.

8)  Reconnect all leads removed from components during testing.
9)  Re-install the outer case (cabinet).

  0)  Reconnect the power supply cord after the outer case is installed.
  )  Run the oven and check all functions.

2.  Follow the troubleshooting guide given below, if indicator does not light up after above check and 

repairs are finished.
)  Disconnect the power supply cord.

2)  Remove the outer case cabinet.

3)  Open the door and block it open.
4)  Discharge high voltage capacitor.
5)  Disconnect the leads to the primary of the power transformer.
6)  Ensure  that  these  leads  remain  isolated  from  other  components  and  oven  chassis  by  using 

insulation tape.

7)  After that procedure, re-connect the power supply cord.
8)  Follow the troubleshooting guide given below for repair. 

 

STEPS 

OCCURRENCE 

CAUSE OR CORRECTION

 

 

The rated AC voltage is not present between   Check supply voltage and oven power cord.

 

 

Pin Nos. 5 and 7 of the 4-pin connecter (CN-A).

 

The rated AC voltage is present at primary  

Touch control transformer or secondary circuit defective.

 

 

side of touch control transformer. 

Check and replace touch control transformer or power unit 

.

TEST PROCEDURES

  PROCEDURE 
 

LETTER 

COMPONENT TEST    

Summary of Contents for KB-6024MK













































Reviews: