Sharp FO 4400 - B/W Laser - All-in-One Operation Manual Download

Page: 45 / 144

Sending a Fax by Automatic Dialing

2. Sending

Documents

Speed Dialing

If the number you want to dial has been programmed in a Speed Dial number,

you can dial it by pressing

and then entering the Speed Dial number.

SPEED DIAL

Load the document(s).

SEND READY will appear in the
display.

•

Press

and/or

set the resolution and contrast if
needed.

•

To send the document ahead of other
documents waiting for transmission,

press

•

To send the document directly from the
feeder (not through memory), press

. (Flip up the Rapid Key overlay

if it is down.)

Press

and then enter the Speed Dial number by pressing the

numeric keys.

•

If you enter less than 2 digits for the Speed Dial number, press

complete the entry.

Check the display. If the name or number shown is correct, press

(If not, press

and then repeat Step 2.)

RESOLUTION

CONTRAST

PRIORITY

DOCUMENT

M/?

SPEED DIAL

START/

ENTER

START/

ENTER

STOP

all.book Page 43 Monday, January 19, 2004 1:02 PM

Summary of Contents for FO 4400 - B/W Laser - All-in-One

















































































































































Search results

Summary of Contents for FO 4400 - B/W Laser - All-in-One

Reviews:

Related manuals for FO 4400 - B/W Laser - All-in-One

Brands by name

Popular brands

Sharp FO 4400 - B/W Laser - All-in-One, Operation Manual

Search results

Summary of Contents for FO 4400 - B/W Laser - All-in-One

Reviews:

Related manuals for FO 4400 - B/W Laser - All-in-One

Brands by name

Popular brands