Please install and adjust the machine according to the requirements of the manual.
Correct operation is very important for your safety.
Unpacking
Unpack the carton and take out the bottom cover.
Open the top lid of washing machine and take out all of the accessories.
Remove all wrappers, including the polystyrene base.
You are advised to keep all the packaging for reuse in case the machine is to be
transported again.
Positioning
Make it horizontal.
Use a tied thread with plumb to check
if it is horizontal.
Adjust the adjustable foot
and twist the adjustable foot.
2) Fasten the nut after adjustment.
Installing the bottom cover
1
°
Adjustable nut
Adjustable
foot
1) Lift up the adjustable foot gently, loose the adjustable nut
Fixing clamp
Scissors
Bottom cover
The base
The distance between the washing machine and the wall should be more than 50mm,
and the maximum allowable angle of the shank base of the machine is 1°
.
The slanting or rough ground may cause operating stopped or unstable, please adjust it
with the following methods:
Let the back of washing machine incline forward,
make the side of the bottom cover with sticker
description facing outside. Insert it to the bottom
of washing machine along the direction of the
arrow.
Remove two fixing clamp by scissors, insert it on
on the cover's aloted holes as shown on the figure
(gently pull fixing clamp and it should not be pulled
out). Make the bottom cover fixed on the base.
1. Abnormal display
1. Abnormal display
E1
E3
E2
F1
E4
E0
Display
Explanation
Settlement
The top lid is opened
when preset is started
Close the top lid and clear up the alarm
The top lid is open when
spinning
Close the top lid and clear up the
alarm
Spin does not balance
Water
level
sensor
is
wrong
Turn the power off and leave it for 1minute.
After that,turn the power on again.
If the same error is displayed,cut the
power suppy and call a technicians.
E5
The top lid is opened
after setting child-lock
child-lock
light flashing
synchronously
Open the top lid and refer to the "before using"
procedures and "common non fault phenomenon"
on this manual to settle it, then close the top lid
and clear up the alarm.
Open the top lid and refer to the "before using"
procedures and "common non fault phenomenon"
on this manual to settle it, then close the top lid
and clear up the alarm.
After 15 minutes of draining
time and still not reaching
the water level setting
After 20 minutes of water
filling time and still not
reaching the water level
setting
4. Child lock function
3. Power supply is cut off automatically
During spinning, if the laundries are not placed equally in the tub, it would cause
violent vibration.This machine has imbalance adjustment function, and the vibration
testing system will supervise the running. Once vibration is beyond certain level,
the adjustment system will start automatically to adjust the imbalance.
2. Imbalance adjustment
1) Press the power supply button and did not start the program in 10 minutes, the
power supply will be cut off automatically.
2) After the washing is finished, buzzer will activate. The power supply will be cut
off automatically.
1) If set child lock function, all the buttons will be locked including POWER. If the top lid is
opened during the washing machine working, the washing will be stopped and give an
alarm.But if you can close the top lid in 5 seconds, the washing machine will stop alarm and
continue working. If can not close the top lid in 5 seconds,the washing machine will begin
draining if there is water in the inner tub is 5 cm higher, alarm will be given every 10 minutes
(alarm is always given). When the draining is finished, the washing machine will be in the
stare of washing, if close the top lid, the washing machine is unlocked and start working as
previous setting.
2) Once child lock is set, if open top lid over 5 seconds during washing or rinse ( there is water
in the inner tub),washing machine will drain and give an alarm. If you unlock the function during
draining, the washing machine will add water to setting water level and continue working.
Open the top lid ,make the laundries
place equally, then close it and clear
up the alarm
Close the top lid and clear up the alarm
