Sharp AR-5015 N Operation Manual Download | Manualshive

Page: 10 / 66

background image

8

GETTING ST

AR

TED

10 cm

Copier installation

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.

Do not install your copier in areas that are:

●

damp, humid, or very dusty

●

exposed to direct sunlight

●

poorly ventilated

●

subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.

The copier should be installed near an accessible power outlet
for easy connection.

Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.

●

For this copier’s power supply requirements, see the name plate located
on the back of the unit.

Connect the copier to a power outlet which is not used
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for
servicing and proper ventilation.

«
...
8
9
10
11
12
...
»

Summary of Contents for AR-5015 N



































































Reviews:

No comments

Related manuals for AR-5015 N

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 11

SmartLink e-STUDIO16

Brand: Toshiba Pages: 14

Brand: Toshiba Pages: 22

Brand: Toshiba Pages: 41

Brand: Toshiba Pages: 90

Brand: Toshiba Pages: 93

Brand: Toshiba Pages: 120

Brand: Toshiba Pages: 168

Brand: Panasonic Pages: 194

WorkCentre Pro 128

Brand: Xerox Pages: 50

Brand: RealSYS Pages: 23

Brand: Lexmark Pages: 85

Brand: Gestetner Pages: 33

Brand: Gestetner Pages: 48

Brand: Gestetner Pages: 548

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands