Sharp AR-281 Operation Manual Download

Page: 87 / 178

5-3

CHAPTER

(A) Open the document feeder cover and remove the original.

●

Rotate the roller in the direction indicated by the arrow to remove
the misfed original.

NOTE:
A message may appear indicating the number of originals which
must be returned to the document feeder tray. Return the originals
and press the START (

) key to resume copying.

Misfeed in the RADF (AR-286 and AR-336)

When the RADF misfeeds an original sheet, the copier will stop and the
misfeed message will appear.

An original misfeed may occur at one of three locations:
(A) in the RADF feed section, (B) in the exit roller, or (C)
under the transport belt.

(A) Open the feeding roller cover and pull the original gently

to the right and out from the document feeder tray.

●

Be sure to open and close the document feeder cover to cancel
the misfeed display.

(B) Open the exit roller cover and gently pull the original

out.

●

Be sure to open and close the document feeder cover to cancel
the misfeed display.

MISFEED REMOVAL

COPIER TROUBLE?

Misfeed removal

A MISFEED HAS OCCURRED.

CLEAR INDICATED AREA.

PRESS FOR RECOVERY INSTRUCTIONS.

Feeding roller cover

Exit roller cover

Roller

Summary of Contents for AR-281



















































































































































































Search results

Summary of Contents for AR-281

Reviews:

Related manuals for AR-281

Brands by name

Popular brands

Sharp AR-281, Operation Manual

Search results

Summary of Contents for AR-281

Reviews:

Related manuals for AR-281

Brands by name

Popular brands