Sharp AR-281 Operation Manual Download | Manualshive

Page: 142 / 178

background image

7-34

CHAPTER

7

Paper size

A4 to A3 (8-1/2" x 11" to 11" x 17")

Paper weight

56 to 105

g

/m

2

(15 lbs. to 28 lbs.)

Paper capacity

500 sheets of paper
Total of 1,000 sheets of paper with an
optional 500-sheet paper drawer installed

Weight

Approx. 25 k

g

(55.2 lbs.)

Dimensions

600 mm (W) x 604 mm (D) x 403 mm (H)

(23-5/8" (W) x 23-25/32" (D) x 15-7/8" (H))

Specifications are subject to change for improvement without notice.

STAND/500-SHEET PAPER DRAWER

(

AR-DE1N

)

This optional stand with a paper tray provides the convenience of
increased paper capacity for the copier and a greater choice of paper
sizes readily available for copying. Even greater paper capacity and
size flexibility are available when the stand is equipped with an op-
tional auxiliary 500-sheet paper drawer (AR-CS1).
The AR-DE1N is available with a 500-sheet paper drawer alone or
with an optional auxiliary 500-sheet paper drawer for the additional
flexibility of two feeds with a total capacity of 1,000 sheets.

PART NAMES

Side cover

500-sheet paper drawer

Optional 500-sheet paper
drawer position

Specifications

OPTIONAL EQUIPMENT

Stand/500-sheet paper drawer (AR-DE1N)

«
...
140
141
142
143
144
...
»

Summary of Contents for AR-281



















































































































































































Reviews:

No comments

Related manuals for AR-281

Brand: Oce Pages: 68

Brand: Oce Pages: 156

Brand: Sharp Pages: 5

Brand: Sharp Pages: 26

Brand: Sharp Pages: 52

Brand: Sharp Pages: 56

Brand: Sharp Pages: 84

Brand: Sharp Pages: 80

Brand: Sharp Pages: 80

Brand: Sharp Pages: 84

Brand: Sharp Pages: 76

Brand: Sharp Pages: 88

Brand: Sharp Pages: 82

Brand: Sharp Pages: 92

Brand: Sharp Pages: 158

Brand: Sharp Pages: 168

Brand: Sharp Pages: 178

Brand: Sharp Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands