Sharp AR-281 Operation Manual Download | Manualshive

Page: 130 / 178

background image

7-22

CHAPTER

7

Staple sort

The STAPLE SORT mode staples A4 (8-1/2" x 11") size copies.
Stapled sets cannot be delivered to the top tray.

NOTE:
Different size originals cannot be copied onto copy paper of their
respective sizes in the STAPLE SORT mode. Only A4 (8-1/2" x 11")
size paper can be selected in the STAPLE SORT mode.

Using the SPF/RADF

1

Set the originals in the document feeder tray.

●

If the number of copies in one set is more than 30, the copies
will not be stapled.

●

If the orientation of the originals does not match that of the copy
paper, the images of the originals will be rotated. The stapling
position in this case is shown below.

AR-281

AR-286/AR-336

●

If originals in the landscape orientation are copied, the copies
will be stapled at an improper position.

AR-281

AR-286/AR-336

2

Press the OUTPUT key.

3

Press the “STAPLE SORT” key on the touch panel.

AR-281

AR-286/AR-336

Stapling position

Stapling position

AUTO

EXPOSURE

READY TO COPY.(DOCUMENT FEEDER MODE)

OUTPUT

TOP TRAY

SORT

OFFSET

TRAY

STAPLE

SORT

GROUP

OK

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

FINISHER (AR-FN2)

OPTIONAL EQUIPMENT

Finisher (AR-FN2)

«
...
128
129
130
131
132
...
»

Summary of Contents for AR-281



















































































































































































Reviews:

No comments

Related manuals for AR-281

Document Centre 470cx

Brand: Xerox Pages: 328

imageRUNNER 105

Brand: Canon Pages: 167

Brand: Canon Pages: 58

Brand: Toshiba Pages: 110

SmartLink e-STUDIO16

Brand: Toshiba Pages: 252

Brand: Ricoh Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands