Sharp AR-162 Operation Manual Download

Page: 48 / 80

GENERAL INFORMA

TION

Problem

Solution

●

Copier plugged in?

●

Power switch ON?

●

Copy density properly adjusted?

●

Is the original placed face down?

●

Paper too heavy?

●

Paper damp?

●

Is transfer charger clean?

●

Non-standard paper used?

●

Paper properly installed?

●

Pieces of paper inside copier?

●

Paper curled or damp?

●

First copy curled?

Plug the copier into a grounded outlet.
See page 8.

Turn the power switch ON.
See page 14.

See pages 14 and 26.

Place the original face down on the original
table.

Use copy paper within the specified range. See
page 49.

Replace with dry copy paper.
Be sure to store copy paper in a dry location. See
page 50.

Clean the transfer charger.
See page 45.

Use standard paper. If using special paper, feed
the paper through the bypass tray.
See pages 18 and 49.

Make sure the paper is properly installed. See
pages 10 and 18.

Remove all pieces of misfed paper.
See page 30.

Store copy paper flat in the wrapper in a dry
location. See page 50.

If the first copy has curled up, flatten it and
change the orientation of the original and copy
paper.

Copier does not operate.

Copies are too dark or
too light.

Blank copies

Paper misfeeds frequently.

Copies smear if rubbed.

COPIER TROUBLE?

Copier trouble?

Striped copies

Paper misfeeds frequently in
two-sided copying.

Summary of Contents for AR-162

















































































Search results

Summary of Contents for AR-162

Reviews:

Related manuals for AR-162

Brands by name

Popular brands

Sharp AR-162, Operation Manual

Search results

Summary of Contents for AR-162

Reviews:

Related manuals for AR-162

Brands by name

Popular brands