background image

SHADOW PANAFLEX WIRELESS 

 Owner’s Manual 

ENGLISH 

 

© Shadow Elektroakustik, Peter-Haendel-Str. 2, DE-91334 Hemhofen / Germany 

Page 6/6 

If you need to select or deselect frequency bands, first you have to set the transmitter to the 

SERVICE MODE

 

ENTER SERVICE MODE: 

 

o

 

The transmitter must be switched off first, then press the switch Tuner 

to start the 

TUNER ONLY MODE

o

 

Press and hold both Wireless ON/OFF 

F

 AND Tuner 

K

 at the same time 

(for ~1 sec.)

 to enter the 

SERVICE MODE

.  

o

 

The LED 

L

 indicates this by alternate flashing between green and red. 

 

SHOW V BATTERY STATE:

 In the 

SERVICE MODE

 press the switch Wireless ON/OFF 

F

:  

o

 

Display 

(Blink code)

 of the hardware version, followed by the battery charge state: 

(lights up for ~4 sec.)

 

 

Blue 

=  Very good condition 

 

Cyan 

=  Good 

 

Green 

=  Normal 

 

Yellow  =  Weak 

 

Red 

=  Very weak 

After showing the transmitter is back in the 

SERVICE MODE

.

 

 

 

SELECT THE FREQUENCY BAND

*

:

 

o

 

First select the 

SERVICE MODE

 than press switch Tuner 

K

. The LED 

L

 flashes fast and shows the actual frequency selection. 

o

 

With the switch Wireless ON/OFF 

F

 you can walk 

(7 steps)

 through the selection as follows: 

o

 

After you set the desired selection, press the switch Tuner 

again.  

The selection is stored and the transmitter is back to the 

SERVICE MODE

.

 

 

USA / EUROPE 

 

JAPAN Version only 

1.

 

White 

=  2.4 + 5.2 + 5.8 *

3

 

2.

 

Red 

=  2.4 

3.

 

Yellow 

=  2.4 + 5.2 

4.

 

Purple 

=  2.4 + 5.8 

5.

 

Cyan 

=  5.2 + 5.8 

6.

 

Green 

=  5.2 

7.

 

Blue 

=  5.8 

 

 

1.

 

White 

=  2.4 + 5.2 *

4

 

2.

 

Red 

=  2.4 

3.

 

Yellow 

=  2.4 + 5.2 

4.

 

Purple 

=  2.4  

5.

 

Cyan  =  5.2 

6.

 

Green  =  5.2 

7.

 

Blue 

=  2.4 

*

3

 Default  (Allowed in USA and Europe)

 

 

*

4

 Default  (Allowed in Japan)

 

 

QUIT SERVICE MODE: 

o

 

Press and hold the switch Wireless ON/OFF 

F

 to switch off the unit. 

 

INVOKE TEST MODE:

 Note: For test and service only!  

o

 

First select the 

SERVICE MODE

o

 

Again press both switches Wireless ON/OFF 

F

 AND Tuner 

K

 at the same time 

(for ~1 sec.)

 to invoke the 

TEST MODE

. Now 

the receiver changes it sound settings automatically controlled by the transmitter. 

o

 

After execution the transmitter switches back to the 

SERVICE MODE

 

 

RESET:  In case of trouble you can reset the system by removing the battery for some seconds.  
 

This will not change the Frequency Band selection! 

TECHNICAL DATA 

 

Power Supply / Charger  100-240VAC 50/60Hz 5V/1.0A switching adapter *

5

 with 3 power adaptors for US, UK, and Europe.  

 

Output socket: USB type A. You can use any other standard 5V USB source to charge. 

(E.g. computer)

 

 

USB Cable(s) 

USB type A to type Micro B 

 

3.7V LI-ION Battery 

Commercial Lithium Ion battery: Like NP60 with a capacity of ~1100mA/h. Running up to 6 hours  

 

RF Frequency 

2.4, 5.2 and 5.8GHz. Indoor use only! 5.2/5.8GHz can be switched off to fulfill the rules and regulation of  

 

your country where you operate this system. 

 

Range 

approx. 100ft. 

(30m)

 – depends on the environment. WLAN devices may disturb proper operation 

 

Transmission 

3 channel digital transmission. 

(2x dig. audio, 1x data)

 

 

Input 

Stereo input for active acoustic or classic-Stereo Nanoflex with 3-pin connector. *

6

  

 

Audio 

2 digital channels with 48kHz sampling frequency  

 

Output Impedance 

6k

 

 

ADC 

Max. 24-Bit Conversion, 114dB Dynamic Range, -105dB THD+N, Overflow Detection 

 

DAC 

Max. 24-Bit Conversion, 113dB Dynamic Range, -94dB THD+N, SNR 113dB 

 

Opt. Output 

S/PDIF, Toslink, Stereo, 16bit, 48kHz, I2S 

 

Latency time 

ca. 6.9ms. This is an additional distance between your instrument and speaker of 7½ft 

(2.3m)

 only! 

*

5

During normal operation or charge operation you may notice a high tone out of the Charger. This is normal and not a malfunction! 

*

String spacing Acoustic pickup: 11mm 

 Classic pickup: 11.8mm 

 

Additional Information about this product 

 

Update information may be found on our website: 

http://shadow-electronics.com

 

There you can find manuals in different languages too. E.g. in German! 

 

Errors and omissions excepted - Subject to change without prior notice! 

 

LED Colors 

Cyan 

Blue and Green 

Yellow 

Green and Red 

Purple 

Red and Blue 

White 

Red, Green and Blue 

*OBEY THE LAWS AND RULES 

IN THE COUNTRY YOU WANT 

TO USE THIS RF SYSTEM! 

Summary of Contents for SH PFA-W







Reviews: