SHADOW PANAFLEX WIRELESS
Owner’s Manual
ENGLISH
© Shadow Elektroakustik, Peter-Haendel-Str. 2, DE-91334 Hemhofen / Germany
Page 5/6
•
BT-T CONTROL:
To control the tone for the lower treble strings [G-B-E]. It works like a bass/treble rocker:
o
Middle position: Flat sound
o
Fig. 6:
If you turn the pot away from the center positions either bass
or treble increases.
If bass is increasing
(A)
the treble will stay flat!
o
Same if you increase treble
(B)
: Bass will stay flat
•
BT-B CONTROL:
o
Same function as BT-T control but controls the sound for the upper strings [E-A-D]
•
OVERLOAD:
The transmitters ADC detects overloaded input signals.
o
If the input is too high
(E.g. heavy strumming)
the LED
L
lights up with all colors, when linked = white for a moment.
Startup the Panorama Receiver
Controls of the Panorama Receiver
Receiver
Front view
Back view
N
PAIRING
Tact switch
O
PAIRING
LED
P
CHARGE LED
Q
CHARGE USB Socket
R
POWER ON/OFF LED
S
POWER ON/OFF Switch
T
MINI-USB 5V Charger socket
U
S/PDIF optical audio output for recording
V
MONO/L Output for Mono or the left channel
W
STEREO/R Output for Stereo or the right channel
Connections
•
POWER:
Connect the USB cable
(type A to MICRO B)
between USB Charger and the rear USB socket
T
of the receiver.
o
The yellow LED
P
lights up and you can use the front USB socket
Q
to charge the transmitter.
•
POWER ON/OFF:
o
Push the switch POWER ON/OFF
S
to switch the receiver on or OFF.
o
The green LED
R
lights up. If equipped, the red SHADOW logo on the front will light up too.
•
AUDIO OUTPUT:
You have 3 options:
o
MONO OPERATION:
Connect a
“Mono Cable”
(TS*
1
plug)
between jack
V
and an amplifier
(E.g. mixer or guitar amplifier)
o
STEREO OPERATION with “2 Mono Cables”:
Connect two cables
(TS plug)
between jack
V
and
W
and two channels of your amplifier.
(E.g. mixer)
o
STEREO OPERATION with a “Y-Cable”:
Connect the stereo plug
(TSR*
2
plug)
to the jack
W
, the opposite ends
(TS plug)
to two channels of a stereo
amplifier. Set the channel 1 and 2 pan pots on the amplifier to the left and
right position!
•
DIGITAL OUTPUT (S/PDIF):
For digital reproduction connect an optical TOSLINK cable
(not provided)
between the TOSLINK
output
U
and your device. First remove the dust cap before you insert the TOSLINK cable. Note that this is the real digital output
signal without Volume, Pan Mute, and BT-T, BT-B control settings. This is best for reworking the digital signal with your audio
software
(not provided)
on the computer. Note: The S/PDIF is affected with a slight pre-emphasis from the transmitter side!
•
USING other transmitter with the receiver:
You always can setup another Shadow transmitter of the same family with the
receiver. Just follow the instruction for
PAIRING
.
Note:
A receiver can play the actual paired transmitter only!
Note:
When you switch the receiver off and on again, it needs a little time until the settings of the transmitter are transferred to the receiver.
During this time you may hear the previous setting shortly before it changes to the new settings. This is normal and not a malfunction!
Special Functions
This system has an intelligent Frequency-Selecting-Procedure. Depending on the environment it searches for the best RF channel.
This works on 3 different frequency bands: 2.4GHz, 5.2GHz and 5.8GHz. In some countries 5.2 and/or 5.8GHz are not allowed. For
this you can deselect these frequency bands. This system has FCC and CE certificates to use all 3 bands in the US and Europe. For
Japan we offer a special version to meet Japanese requirements. It is possible that RF regulations in your country may vary after
printing this manual. In case you need updated information please visit our website for the latest manuals.
*
1
TS: Tip, Sleeve of a ¼” mono plug
*
2
TSR: Tip, Sleeve, Ring of a ¼” stereo plug
Fig. 6
