15
Level 1
Level 2
Level 3
Level 4
Function
SETTINGS
WIRELESS DMX
Log Off
-
Press ‘OK’ to log off wireless DMX.
STATUS
Signal Strength %
Display the signal strength % of the connection.
CRMX PAIRD
Display CRMX PAIRD: YES or NO.
DMX Active
Display DMX Active: YES or NO.
CRMX RATE
Display CRMX RATE (oH2).
ENABLE
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
DIMMING CURVE
LINEAR
Press ‘OK’ to select linear dimming.
GAMMA CORRECTED
Press ‘OK’ to select gamma corrected dimming.
INVERT PAN
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
INVERT TILT
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
SWAP PAN TILT
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
FLIP DISPLAY
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
DISPLAY OFF
[X] / [ ]
Press ‘OK’ to enable / disable - [X] / [ ].
FAN MODE
Standard
Fan speed acording to internal fixture temperature.
Silent
Low fan speed for quiet operation.
Max Power
High fan speed for better cooling effect.
Always 100%
Always maximum fan speed for high cooling effect.
CALIBRATION
PAN HOME
CALIBRATION → XXXXX
Pan Pos XXXX - REV. X.XX
Display PAN HOME position. Scroll 'UP' and 'DOWN' to define PAN
HOME position. Confirm with 'OK'.
TILT HOME
CALIBRATION → XXXXX
Pan Pos XXXX - REV. X.XX
Display TILT HOME position. Scroll 'UP' and 'DOWN' to define TILT
HOME position. Confirm with 'OK'.
GOBO 1 SELECT
CALIBRATION → XXXXX
Define home position for each effect.
Scroll 'UP' and 'DOWN' to define home position for each position.
Confirm with 'OK'.
GOBO 2 SELECT
CALIBRATION → XXXXX
EFFECT WHEEL 1
CALIBRATION → XXXXX
EFFECT WHEEL 2
CALIBRATION → XXXXX
FROST
CALIBRATION → XXXXX
PRISM
CALIBRATION → XXXXX
IRIS
CALIBRATION → XXXXX
SERVICE PIN
-
Service use only.
Contact your SGM dealer or SGM support to request the service pin.
SERVICE MENU
FIXTURE TYPE
Service use only.
DEBUG
LINK QUALITY
MINIMUS LEVELS
Recalibration SMPS
FACTORY DEFAULT Factory default / set
Press 'OK' to set the fixture to factory default and 'ESC' to unset.
See 'Factory default' on page 13
.
TEST
OFF
-
Stops test sequence execution.
AUTOMATED TEST
-
Initiates a self-test sequence. Select 'OFF' to stop self-test sequence.
LED TEST
Testing Red 2
Scroll 'UP' and 'DOWN' to test the different colors.
Service use only.
Testing Red 1
Testing Blue 2
Testing Blue 1
Testing Yellowish Green
Testing Green
DISPLAY TEST
-
Service use only.
RESET
PAN TILT
Press ‘OK’ to reset the PAN TILT.
EFFECT MODULE
Press ‘OK’ to reset the EFFECT MODULE.
Zoom Focus Module
Press ‘OK’ to reset the ZOOM FOCUS MODULE.
ALL
Press ‘OK’ to reset all.*
Control menu - continued
*When the G-Spot Turbo is subjected to extreme exposure it might not reset correctly. Should this be the case, the fixture will automatically heat up the gobo bearings
at maximum light output for approx. five minutes and attempt to reset the fixture again. If this not solve the issue, disconnect the fixture from power and power it back, to
repeat the heat-up procedure. If none of this resolve the issue, contact your local SGM distributor or SGM Technical Support. See http://sgmlight.com for more details.
