background image

SGM 

   

GB 

 

Fazer 1000 

 

 

Danger of Explosion 

 

 

Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid. 

 

Use only the high-quality, water-based SGM fog liquid. (FLG) Other fog liquids 

may cause clogging or "spitting". 

 

Always make sure there is sufficient liquid in the fog liquid tank.    Operating this 

unit without liquid will cause damage to the pump as well as over-heating of the 
heater. 

 

If your SGM Fog Machine fails to work properly, discontinue use immediately.   

Drain all fog liquid from the tank, pack the unit securely (preferably in the original 
packing material), and return it to your SGM dealer for service. 

 

Always drain tank before mailing or transporting this unit. 

 

Never drink fog liquid.    If it is ingested, call a doctor immediately.    If fog liquid 

comes in contact with skin or eyes, rinse thoroughly with water. 

 

Important! 

Pay attention to all warning labels and instructions printed on the exterior of your SGM   

Fazer 1000. 

 

3.

 

U

NPACKING 

&

 

I

NSPECTION

 

Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact.   
 
Before beginning initial setup of your SGM Fog Machine, make sure that there is no evident damage caused 
by transportation.    In the event that the unit's housing or cable is damaged, do not plug it in and do not 
attempt to use it until after contacting your SGM dealer for assistance. 
 
The shipping carton should include the following items: 

1

 

Fazer 1000 machine with power cable 

2

 

X-10 Control Module 

3

 

Fluid Tank 

4

 

User manual 

Before beginning initial setup of your Fazer 1000, make sure that there is no evident damage caused by 
transportation In the event that the unit's housing or cable is damaged, do not plug it in and do not attempt 
to se it until after contacting your SGM dealer for assistance. 
 

4.

 

S

ETUP

 

1

 

Remove all packing materials from shipping box.    Check that all foam and plastic padding is removed, 
especially in the nozzle area. 

2

 

Place fog machine on a flat surface and remove fog liquid tank cap. 

3

 

Fill with only SGM Fog Fluid. SGM Fazer 1000 only works with uncontaminated SGM FLG Fog Fluid. Other   
fluids  may  cause  spitting  and  serious  clogging  problem  and  could  result  in  the  production  of  an 
unhealthful fog. The use of other fluids will void the warranty of the SGM Fazer 1000. When filled, place 
cap back on liquid tank. 

Firmly attach the control module cable to the connector inside the rear chamber of the machine.     

 

WARNING! 

Use of any fluid other than SGM fog fluid or modification or attempted to unauthorized repair of the 

Fazer 1000 will immediately invalidate the warranty.

 

www.audiovias.com

Summary of Contents for FAZER 1000










Reviews: