background image

4

Operating instructions – BMG..T Double Disc Brakes for Stage Applications

1

Safety and warning instructions

Important Notes

Betriebsanleitung

1

Important Notes

1.1

Safety and warning instructions

Always follow the safety and warning instructions in this publication!

This documentation contains safety requirements and additional information on the
BMG..T double disc brake for use in stage applications. 

A requirement of fault-free operation and fulfillment of any rights to claim under
guarantee is that you adhere to the information in the operating instructions.
Consequently, read the operating instructions before you start working with the brake!
The operating instructions contain important information about servicing and should be
kept close to the unit. This document supplements the "AC Motors, Asynchronous
Servomotors" operating instructions and limits the application notes according to the
following information.

The guidelines in this documentation must be strictly observed for safety
applications. This applies in particular to the requirements of the employer's
liability insurance association and TÜV.

Disposal 

This product consists of:

Iron

Copper

Aluminum

Plastic

Please dispose of the parts in accordance with the applicable regulations.

Electrical hazard
Possible consequences: Severe or fatal injuries.

Hazard 
Possible consequences: Severe or fatal injuries.

Hazardous situation
Possible consequences: Slight or minor injuries.

Harmful situation
Possible consequences: Damage to the unit and the environment.

Tips and useful information.

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for BMG T Series















Reviews: