background image

8

Operating instructions – BMG..T Double Disc Brakes for Stage Applications

5

Mechanical installation

Installation/Startup

5

Installation/Startup

5.1

Mechanical installation

In normal operation, the manual release lever for the brake must not be
attached. This prevents the brake from being released unintentionally.

The drive may only be installed if

The drive is undamaged (no damage caused by transportation or storage)

It is certain that the following requirements have been met:
– Ambient temperature between -25 °C and +40 °C 
– No oil, acid, gas, vapors, radiation, etc.
– Installation altitude max. 1000 m above sea level

5.2

Electrical installation

As regards the safety of the switching equipment, it must comply at least with
category 3 to EN 954-1 or with a comparable national standard.

The utilization category of the contactors for the brake control system must be
at least AC-3 in accordance with EN 60947-4-1 or a comparable national
standard.

The brake is released electrically. The brake is applied mechanically when the
voltage is switched off.

– Connect the brake according to the wiring diagram supplied with the brake.
– The supply voltage must lie within the rated voltage range of the brake coil (see

Sec. "Technical Data").

The brake can only be run with the SEW brake control system it is intended for (see
Sec. "Technical Data").

Check the line cross sections – operating currents (see Sec. "Technical Data").

– Apply brake voltage according to the nameplate.
– Connect the brake control system according to the wiring diagram supplied with

the brake.

– For motors in thermal class H, install the brake rectifier in the switch cabinet!
– Use only copper cables with the following temperature ranges as connection

cables: Temperature range: 60/75 °C

Comply with the applicable regulations issued by the relevant employer's
liability insurance association regarding phase failure protection and the
associated circuit/circuit modification!

5.3

Startup

For startup, in addition to the safety notes in these operating instructions, it is essen-
tial that you comply with the safety notes in the operating instructions for the motor
as well as the legal and liability insurance conditions.

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for BMG T Series















Reviews: