background image

15

© Setra Systems, Inc. All Rights Reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc.

13.0 Warranty and limitation of liability

SETRA warrants its products to be free from defects in materials and workmanship, subject to the following terms and 

conditions: Without charge, SETRA will repair or replace products found to be defective in materials or workmanship within 

the warranty period; provided that:

a) the product has not been subjected to abuse, neglect, accident, incorrect wiring not our own, improper 

installation or servicing, or use in violation of instructions furnished by SETRA;

b) the product has not been repaired or altered by anyone except SETRA or its authorized service agencies;

c) the serial number or date code has not been removed, defaced, or otherwise changed; and

d) examination discloses, in the judgment of SETRA, the defect in materials or workmanship developed under 

normal installation, use and service;

e) SETRA is notified in advance of and the product is returned to SETRA transportation prepaid.

Unless otherwise specified in a manual or warranty card, or agreed to in writing and signed by a SETRA officer, SETRA pres-

sure, humidity, and acceleration products shall be warranted for one year from date of sale.  

The foregoing warranty is in lieu of all warranties, express, implied or statutory, including but not limited to, any implied war-

ranty of merchantability for a particular purpose. 

SETRA’s liability for breach of warranty is limited to repair or replacement, or if the goods cannot be repaired or replaced, to 

a refund of the purchase price. In no instance shall SETRA be liable for incidental or consequential damages arising from 

a breach of warranty, or from the use or installation of its products. No representative or person is authorized to give any 

warranty other than as set out above or to assume for SETRA any other liability in connection with the sale of its products.

For all CE technical questions, contact Setra Systems, USA. EU customers may contact our EU representative Hengstler 

GmbH, Uhlandstr 49, 78554 Aldingen, Germany (Tel: +49-7424-890; Fax: +49-7424-89500).

Summary of Contents for SRH400

















Reviews: