background image

13

© Setra Systems, Inc. All Rights Reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc.

General

Supply voltage (Class III)

for 0-10 V output:

15-35 VDC or 15-29 VAC

for 4-20 mA output:

10 -35 VDC

Current consumption

DC supply:

typ. 10 mA

AC supply:

typ. 20 mA

Load resistor (for 4-20 mA output)

R

L

 < (U

V

-10 V/0.02 A)[Ω]

Connection

Screw terminals, max. 2.5 mm

2

Housing material

Cast away - AlSi

9

Cu

3

Protection class

IP65/ NEMA 4

Outputs

0-100% RH

0-10 V: 

-1 mA < I

L

 < 1 mA

4-20 mA (2-wire):

R

L

 < 500 Ω 

T dependence of analog outputs

Max. 0.2 mV/°C

Resp. 1 μA/°C

General (cont.)

Cable fitting

PG9

cable Ø 4.5-100 mm (0.18-0.39”)

Sensor protection

Membrane filter

Electromagnetic compatibility

EN61326-1, EN61326-2-3, Industrial environment

Temperature ranges

Operating: -40 to  60°C (-40 to 140°F)

Storage:  -40 to  60°C (-40 to 140°F)

10.0 Technical data

11.0 Spare parts and accessories

Specifications subject to change without notice.

Category

EE Accessory P/N

Setra Accessory P/N

Description

Filters

HA010101

SRHMF

Membrane filter

Filters

HA010103

SRHSS

Stainless steel sintered filter

Filters

HA010104

SRHPG

Plastic grid filter

Filters

HA010105

SRHPF

PTFE - filter Ø12mm

Filters

HA010106

SRHMG

Metal grid filter

Filters

HA010115

SRHHP

H2O2 - filter

Flanges

HA010201

SRHSMF

Stainless steel mounting flange 12mm

Flanges

HA010209

SRHDMK

Duct mounting kit (for SRH400)

Flanges

HA010211

SRHWMC

Wall mounting clip for probe Ø12mm

Flanges

HA010214

SRHPMFB

Plastic mounting flange 12mm; black

Flanges

HA010202

SRHPMFG

Plastic mounting flange 12mm; grey (RAL7035)

Part configuration adapter

EE-PCA

SETRAPCA1

Configuration adapter transmitter to RS232 and USB

Part configuration adapter

HA011057

SETRAPCA4

Configuration cable for humidity & temp probe SRP4xxx

Cable for SRH400

HA010801

SRC400W

Remote probe extension cable - 2 meter

Cable for SRH400

HA010802

SRC400F

Remote probe extension cable - 5 meter

Cable for SRH400

HA010803

SRC400X

Remote probe extension cable - 10 meter

RH & temp sensor probe SRH400

EE07-MFT6HC01

SRP400HTMGM

SRH400 humidity/ temperature sensor with coating

Temp sensor probe SRH400

EE07-MT

SRP400TPNNM

SRH400 temperature sensor

Calibration

ISO-AH3ASD

SRH400SCAL

SRH400 calibration (ISO)

Calibration

OEKD-AH3A1SD

SRH400NCAL

SRH400 calibration (NIST)

Summary of Contents for SRH400

















Reviews: