SES SAT DBPX Page 9 User/Installer Manual Download | Manualshive

Page: 9 / 36

background image

SAT DBRX V1.0

SELECT ENGINEERED SYSTEMS 06/93

POWER POWER POWER
SWITCH FUSE CONN.

16 VAC
16VAC
GND

TBS-1
TBS-2
TBS-3

Recommended wire gauge is as shown: 16 ga. up to 50 feet.

14 ga. up to 100 feet.
12 ga. up to 200 feet.
10 ga. up to 300 feet.
8 ga. up to 500 feet.

CONNECTING GROUND AND POWER

1) Connect a 16 gauge wire from the ground terminal (TBS-3) of the terminal barrier strip as shown
above to a good earth ground. Do this before connecting anything else to the SAT DBRX.
2) Connect the wires for the power connections to TBS-1 and TBS-2, as shown. Connect the other
ends of the wires to the screws on the supplied transformer (16 vac 15 va). Determine the gauge size
from the table below.

In the event of a voltage surge or other electrical transient, the fuse may need to be replaced.

Replace with a 1 AMP slo-blo fuse only.

«
...
7
8
9
10
11
...
»

Summary of Contents for SAT DBPX





































Reviews:

No comments

Related manuals for SAT DBPX

Brand: GE Pages: 146

Brand: GE Pages: 4

Brand: NAIM Pages: 2

Brand: NEC Pages: 6

Brand: Profile Pages: 6

Brand: Fostex Pages: 20

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Brand: Lancom Pages: 70

kontron COMe-cEL6

Brand: S&T Pages: 99

Millennium P650

Brand: Matrox Pages: 54

REJ06B0734-0100

Brand: Renesas Pages: 19

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: Variscite Pages: 17

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: McIntosh Pages: 44

Brand: ICP DAS USA Pages: 8

Brand: Roland Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands