Servomech ATL 02 Installation, Operation And Maintenance Manual Download Page 2

Servomech S.p.A. 

02.02-05-08-10-11-12.E - Rev. 00 Date (M/Y) 12/19 

 WARNING

 

Read this manual before installing, operating or maintaining this actuator. Failure to 
follow safety precautions and instructions could cause actuator failure and result in 
serious injury, death or property damage. 

This manual provides important information on how to work with the actuator safely 
and efficiently. The manual is part of the device, must always be kept in the device’s 
direct proximity and should be available for personnel to read at any time. Failure to 
comply  with  the  installation,  use  and  maintenance  instructions  indicated  in  this 
manual  will  result  in  immediate  termination  of  the  warranty  conditions  of  the 
actuator  and  completely  relieve  Servomech  S.p.A.  from  any  liability  for  damage 
caused to persons and / or property. 

Servomech S.p.A. it does not assume direct or indirect responsibility for an improper 
use of the actuator, not respecting the performances of the actuator declared in the 
catalogs. 

The manufacturer will not be liable for damage to the actuator or the equipment into 
which the actuator has been installed resulting from: 

• disregarding this manual 
• unintended use 
• employment of untrained personnel 
• unauthorized conversions 
• technical modifications 
• manipulation or removal of the screws on the device 
• use of unapproved spare parts 

The  aforementioned  conditions  are  therefore  not  contemplated  and  entail  the 
immediate  termination  of  the  guarantee  and  the  immediate  decay  of  any 
responsibility on the part of Servomech S.p.A. 

Servomech S.p.A. reserves the right to make changes to the actuators and this manual 
without giving any notice. 

Summary of Contents for ATL 02






















Reviews: