manualshive.com logo in svg

Serious Integrated SIM225, Technical Reference Manual

Share
Download
Serious Integrated SIM225 Technical Reference Manual Download Page 36

SIM225 Technical Reference Manual 

36 

 

© Serious Integrated, Inc. 

SIM225_TRM_A1ENUS 

Revision A1 

 

 

Location

 

Size 

(Bytes)

 

Contents

 

0x00..0x07 

8 

Unique Microchip SST25V064 Serial Number 

0x08..0x09 

2 

0x0225 indicates SIM225 

0x0A 

1 

Version of hardware: high nibble is major; low nibble is 

minor. For example, “0x14” is v1.4 

0x0B 

1 

Variant of hardware: see chart below  

0x0C..0x0F 

4 

Unique sequence number of this model/variant 

0x10..0x17 

8 

Reserved for custom OEM Serial Number 

0x18..0x1F 

8 

Reserved for 

Serious manufacturing information 

Locations 0x08…0x0F, when combined, form the unique 

Serious serial number for the module. All values 

are stored in 

Big Endian

 order. Note that the MCU on the SIM is normally operated in Little Endian mode, 

so byte/word swapping will be required to correctly interpret the data. 

The following table maps the Variant ID byte found in the primary SIM25VF064C’s OTP area at location 
0x0B to the SIM225 variant name.  

Variant ID Byte

 

SIM225 Variant Name

 

0x00 

-A00 

0x01 

-A01 

0x02 

-A02 

0x03 

-A03 

0x04 

-A04 

0x99 

Renesas YLCDRX63N 

0xFF 

Invalid/Unknown 

All others 

Reserved 

UNIVERSIAL SERIAL BUS (USB) 

All SIM225 variants have a single USB 2.0 Full Speed (12Mbit/s) device (or “function”) capability, though 
not all variants have the associated mini-B connector.  The USB Device signals are also available on other 
connectors, including 

the PCB Edge Connector

 and the Baseboard Connector (when present). 

Some SIM225 variants also have a USB 2.0 Full Speed embedded host “A” connector and associated 
capability for (typically) support of USB thumb drives, keyboards, mice, etc. 

The following chart lists the current SIM225 variants and the USB options: 

SIM225 

Variant

 

USB Device 

USB Embedded Host 

Circuitry 

Mini-B 

Connector  Circuitry 

A 

Connector 

-A00 

 

 

 

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for SIM225




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands