manualshive.com logo in svg

Serious Integrated SIM225, Technical Reference Manual

Share
Download
Serious Integrated SIM225 Technical Reference Manual Download Page 10

SIM225 Technical Reference Manual 

10 

 

© Serious Integrated, Inc. 

SIM225_TRM_A1ENUS 

Revision A1 

 

 

GETTING STARTED 

The SIM225 comes pre-configured with a demo program loaded in the system 
FLASH.  To startup the system, plug a USB cable from your PC or USB supply 
into the USB device Mini-B connector.  The system will use a maximum of 
500mA of current from the USB connection when in operation. 

The demo will  start running and displaying  info  on the LCD screen.  For more 
getting started information and out-of-the-box tips, see 

www.seriousintegrated.com/oob

. 

 

Several connectors may be used to power the SIM225. See 

Power Supplies

.   

 

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for SIM225




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands