manualshive.com logo in svg

Serious Integrated SIM225, Technical Reference Manual

Share
Download
Serious Integrated SIM225 Technical Reference Manual Download Page 11

SIM225 Technical Reference Manual 

11 

 

© Serious Integrated, Inc. 

SIM225_TRM_A1ENUS 

Revision A1 

 

 

SPECIFICATIONS 

DC POWER CHARACTERISTICS 

VARIANTS WITH LIPO SUPPORT 

The following DC characteristics apply 

only to variants with LiPo capabilities, including the SIM225-A00. 

Specification 

LCD 

Backlight 

State 

USB 

Host 

State 

LiPo 

State

4

 

Audio 

Amp 

State 

Permissible Range 

Min 

Typ 

Max  Units 

Input Supply V5V_USBF 

- 

- 

- 

- 

4.75 

5.00 

5.25 

V 

Input Supply C5V_USBF 

off

 

off

 

N 

off

 

 

25

1,3

 

tbd

1,2

 

mA 

100% 

off 

N 

off 

 

141

1,3

 

tbd

1,2

 

mA 

100% 

on

 

N 

on

 

 

141

1,3

 

tbd

1,2

 

mA 

any

 

any

 

C 

any

 

 

 

500 

mA 

Input Supply V5V_EXT  

- 

- 

- 

- 

4.35 

5.00 

5.25 

V 

Input Supply C5V_EXT 

off

 

off

 

N 

off

 

 

25

1,3

 

tbd

1,2

 

mA 

100%

 

off 

N 

off 

 

141

1,3

 

tbd

1,2

 

mA 

100%

 

on

 

N 

on

 

 

tbd

1,3

 

tbd

1,2

 

mA 

any

 

any

 

C 

any

 

 

 

tbd

1,2

 

mA 

Charging Current to LiPo Battery 

any

 

any

 

C 

any

 

 

 

480 

mA 

Notes: 

1

Any additional external current draw from the module is in addition to this value 

2

At minimum voltage on supply 

3

At typical input supply voltage 

4

 LiPo Status: N = not draining nor charging, or not present, C = Charging, D = Draining 

VARIANTS WITHOUT LIPO SUPPORT 

The following DC characteristics apply 

only to all variants without LiPo capabilities, including the SIM225-

A01, A02, A03, and A04. 

Specification 

LCD 

Backlight 

State 

USB 

Host 

State 

Audio 

Amp 

State 

Permissible Range 

Min 

Typ 

Max  Units 

Input Supply V5V_USBF 

- 

- 

- 

4.75 

5.00 

5.25 

V 

Input Supply C5V_USBF 

off

 

off

 

off

 

 

25

1,3

 

tbd

1,2

 

mA 

100% 

off 

off 

 

141

1,3

 

tbd

1,2

 

mA 

100% 

on

 

on

 

 

141

1,3

 

tbd

1,2

 

mA 

any

 

any

 

any

 

 

 

500

4

 

mA 

Input Supply V5V_EXT  

- 

- 

- 

3.60 

5.00 

6.00 

V 

Input Supply C5V_EXT 

off

 

off

 

off

 

 

25

1,3

 

tbd

1,2

 

mA 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for SIM225




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands