3
★
For safes with 3-Number Combination Lock
NOTE: See the sticker on the back cover of this manual for y
our combination.
IMPORTANT: The lock on this safe is in the open position. DO NOT operate the
combination until first reading and understanding the following instructions.
Test first with door open!
Test your combination several times with the door open, to make sure you have recorded it
correctly. Your combination is ready to use.
COMBINATION:
3-Number Combinations
1.
Start with dial on zero.
2.
Turn dial
LEFT
two turns and stop on the first number
of the combination the third time.
3.
Turn dial
RIGHT
passing the second number of the
combination once, stopping on the number the second time.
4.
Turn dial
LEFT
stopping first time on
To Close and Lock
With the door closed, spin the combination dial several times.
★★
For safes with UL Group 2 Combination Lock
NOTE: See the sticker on the back cover of this manual for your combination.
IMPORTANT: The lock on this safe is in the open position. DO NOT operate the
combination until first reading and understanding the following instructions.
Lock Test
Test first with door open!
Test your new UL Listed combination lock several times with the door wide open. First turn the dial
to the right until it stops at approximately 87, then turn the safe handle clockwise until it stops.
Open the door as far as it will go and turn the safe handle counterclockwise until it stops and the
live locking bolts are extended. Carefully follow the instructions below.
NOTE: The dial will not turn past zero unless the bolts are in the locked position
with the handle vertical.
Accurate alignment of the lock with the opening index (the vertical line at the top-center of the
dial) is essential for successfully operating your combination. Dial your combination slowly and
carefully to avoid passing the desired numbers. Should you dial past the correct number, the entire
combination will need to be re-entered. To avoid damaging the lock mechanism, never spin the dial
back and forth rapidly.
COMBINATION:
1.
Start with dial on
ZERO
.
2.
Turn the dial to the
LEFT
(counterclockwise). Pass the first number of the
combination three times. Stop on the first number of the combination the fourth time.
3.
Change the direction you are dialing. Going
RIGHT
(clockwise), pass the second
number of the combination two times and stop on the second number the third time.
4.
Change directions again. Turning
LEFT
(counterclockwise),
pass the third number of the combination once and then continue
around in the same direction, stop on the third number of the combination.
5.
Change directions again, turning
RIGHT
until the dial stops completely and will not move.
6.
Turn safe handle upward, to the left (clockwise) and open the door.
To Close and Lock
With the door closed, turn the handle counterclockwise to secure the locking bolts, then spin the
combination dial to the left at least four times to scramble the combination.
Lost combination
First, find your safe’s Serial Number. The Serial Number is printed on the small label on the right
side of the safe (outside). Send this and a check or money order for $12.00 (U.S. funds). Please
include a written statement of ownership witnessed and signed by a notary public or bank official.
The notary must have a different last name than the owner. Mail to: Sentry Group, Dept. 200,
882 Linden Avenue, Rochester, NY 14625-2784, USA, or fax statement (notary seal must be legible)
to 1-585-381-2940. Payment may also be made using your VISA or Mastercard credit card by phone
only. Call 1-800-828-1438 to make credit card payment. Do not fax credit card information.
*
NOTE: Prices subject to change without prior notification.
The sticker on the back cover of this manual contains the serial number and factory code for your
safe. It is important that you keep this Owner’s Manual in a secure place,
other than in your
safe,
for future reference.
Using the keypad on electronic safes
Caution!
Liquids can damage the keypad!
Caution!
Pen points or other sharp objects can puncture
the keypad membrane!
★★★
Standard Electronic Lock
To activate lock
Four alkaline AA batteries, Voltage: 6Vdc, (not included) are required to activate the keypad.
NOTE:
Non-alkaline and rechargeable batteries
ARE NOT RECOMMENDED
.
To install batteries:
1.
Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad
with your thumbs, and disconnect it from the safe by pulling it towards you. (Fig. A)
2.
Let the disengaged keypad hang by its wires. This will expose the battery holder. (Fig. B)
3.
Install four alkaline AA batteries as illustrated on the back of the battery holder.
4.
Reconnect the keypad by inserting the keypad's four posts into the matching holes.
5.
Push down to snap into place.
A
B
Battery
Holder
Summary of Contents for ProStaff
Page 19: ...19 ...
