background image

11

English

Bolting Down Your Safe

Bolt-down instructions 

NOTICE

  

Product is not water resistant once it is bolted down. The ETL verified water resis-
tance claim applies to product prior to the application of a bolt-down kit.

Bolt-down kit contents (in select models only):

•  2 lag screws 
•  2 washers 
•  2 masonry anchors

Tools needed to bolt safe to the floor:

• Drill 
• Wrench 
• 

7

16

” (11 mm) drill bit – for drilling into the safe 

• 

9

32

” (7.2 mm) drill bit – for drilling into a wood floor 

• 

3

8

” (9.5 mm) drill bit – for drilling into a masonry floor

Warning:  • DO NOT drill from any location inside the safe.

 

• DO NOT bolt through the walls.

 

1

  Tip the safe onto its right side (door hinges horizontal with the floor).

 

2

 

Unlock the safe and open the door. Look to the bottom of the 
safe for two indentations on the feet in opposite corners. Using 
the 

7

16

” (11 mm) bit; drill a hole through each indentation 

perpendicular to the bottom of the safe. 

DO NOT drill from 

any location inside the safe.

 

3

  Tip the safe upright, place the safe in the desired location  and open the door.

 

4

 

Use a screw or pencil to mark the floor through both holes.

F

F

Summary of Contents for Fire-Safe
















Reviews: