manualshive.com logo in svg

Sentex Crown Jewel, Installation Manual, Page: 18 / 24

Share
Download
Sentex Crown Jewel Installation Manual Download Page 18

18

ADJUST THE AUDIO

3. Press 

the unit will emit a 45 second tone. 

 

While the tone is being emitted, adjust the “FEEDBACK/VR2” 
dial until the tone is it’s minimum level.

2. Enter six-digit password (Default = 000000). The unit will beep two times.

1. Press 

on the unit’s keypad. 

4. Press  

to discontinue the tone.

5. Press 

to exit programming. The unit will emit 3 short beeps.

TB3 PHONE LINE

TB5

HOUSE TELCO

KEYPAD

DS4

MIC

"SLIC"

DS3

"HOME"

VR2
"FEEDBACK"

EARTH GND

4

Audio Feedback must be set accurately to ensure proper operation. The factory
setting is indicated by a mark on the rim of the “FEEDBACK” dial “VR2”.

ADJUST AUDIO FEEDBACK

2. If the speaker volume is either too loud or too soft, adjust
    the volume using the “Speaker Level/VR1” dial. 

3. When the speaker volume is set to the desired 
    level. end the call by hanging up (or press     ).

1. Place a call from the unit to the resident’s 
    telephone and speak.

EXIT

EXIT

A

UT

OCALL

TB3 PHONE LINE

TB5

COM

HOUSE TELCO

KEYPAD

VR1
"SPEAKER LEVEL"

DS1

DS55

DS4

MIC

"HOLD"

"SLIC"

"TELCO"

DS3

"HOME"

VR2
"FEEDBACK"

EARTH GND

2

The speaker volume may need to be adjusted for proper audio
due to inconsistent phone lines. The factory setting is indicated
by a mark on the rim of the dial. To increase volume, turn the
dial clockwise. 

ADJUST AUDIO VOLUME

Summary of Contents for Crown Jewel

























Reviews:

No comments