background image

www.sentera.eu

MIW-SDX-Y-EN-000 - 31 / 03 / 2022

4 - 8

back to the table of contents

SD

ELECTRONIC FAN SPEED 
CONTROLLER

PRODUCT DESCRIPTION

These infinitely variable fan speed controllers allow you to manually adjust the 
rotational speed of single phase AC motors by varying the motor voltage through 
phase angle control. The integrated AC switch enables or disables the motor.  

ARTICLE CODES

Output regulation from low to high

Code

Current range [A] 

SDY-1-15-DT

 1—1,5

SDY-1-30-DT

0,2—3

Output regulation from high to low

Code

Current range [A] 

SDX-1-15-DT

 1—1,5

SDX-1-30-DT

0,2—3

INTENDED AREA OF USE

 

Manual control of the motor / fan speed in HVAC applications

 

For indoor use only

TECHNICAL DATA

 

Supply voltage: 230 VAC / 50—60 Hz

 

Regulated output to motor: Umin—Us

 

Unregulated output: 230 VAC / max. 2 A

 

Minimum speed adjustment by trimmer: 80—180 VAC

 

Speed control:

 

SDY—from low to high

 

SDX—from high to low

 

Enclosure: 

 

External: ASA, white colour (28049P ), IP54 (according to EN 60529)

 

Internal: polyamide, natural colour, IP44 (according to EN 60529)

 

Operating ambient conditions:

 

temperature: 0—40 °C

 

rel. humidity: 5—95 % rH (non-condensing)

STANDARDS

 

Low Voltage Directive 2014/35/EU 

 

 EN 60529:1991 Degrees of protection provided by enclosures (IP Code) 
Amendment AC:1993 to EN 60529

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

EMC directive 2014/30/EU:

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

 EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic 
standards - Immunity for residential, commercial and light industrial environments

 

 EN 61000-6-3:2007 Electromagnetic compatibility (EMC) - Part 6-3: Generic 
standards - Emission standard for residential, commercial and light-industrial 
environments Amendments A1:2011 and AC:2012 to EN 61000-6-3

 

WEEE Directive 2012/19/EU

 

RoHs Directive 2011/65/EU

Summary of Contents for SD









Reviews: