SenTech STC-GE83A User Manual Download Page 25 | Manualshive

Page: 25 / 44

background image

STC-GE83A

STC-GEC83A

User Guide

25

Rev 1.01

Command No.

Command Description

13H:
MOD4[7..0]

[Camera function mode 4] Initial data: MOD4[7..0] = 60H
Sets the camera function mode.
D[7..0]

D7

D6

D5

D4

D3

D2

D1

D0

D7:

No Function

Always set as “0”

D6:

Trigger signal mask during exposure

0: OFF (No mask)

1: ON (Mask)

D5

Trigger signal mask during image output

0: OFF (No mask)

1: ON (Mask)

D4 to D0:

No Function

Always set as “100000”

Note 1: The trigger signal is invalidated when mask function is on.

16H:
SOFTRG[7..0]

[Software Trigger Setting] Initial data: SOFTRG[7..0] = 80H
Sets the source of the software trigger.
D[7..0]

D7

D6

D5

D4

D3

D2

D1

D0

D7 to D6:

Software trigger source selection

00: Programming software trigger

10: Command software trigger
(200 useconds pulse width trigger signal)

01, 11: No function
(Prohibited settings. Do not set these values)

D5 to D1:

No Function

Always set as “00000”

D0:

Generate software trigger command

0: Hold (Low State)

1: Generate command software trigger

(200 useconds high state)

Note 1: The software trigger source selection is enabled whenever “Trigger signal type (MOD3-D5)” is the software

trigger (set as 0)

Note 2: The “Programming software trigger” is used to set up the pulse duration, trigger signal interval and generate the

trigger signal.

Note 3: When selecting “Command software trigger”, it is necessary to generate the software trigger signal with the

“Generate command software trigger (SOFTRIG-D0)”.

17H:
IMAGEREST
[7..0]

[Image Data Reset] Initial data: IMAGEREST[7..0] = 00H
Reset the Image data (FVAL, LVAL and the image data).
Change from the reset to the image data out after starting the image acquisition.
The image data is not output when resetting the image data.
D[7..0]

D7

D6

D5

D4

D3

D2

D1

D0

D7 to D1:

No Function

Always set as “0000000”

D0:

Image Data Reset

0: FVAL/LVAL/Image data reset
(FVAL, LVAL and the image data are low state data)

1: FVAL/LVAL/Image data out

«
...
23
24
25
26
27
...
»

Summary of Contents for STC-GE83A













































Reviews:

No comments

Related manuals for STC-GE83A

Brand: Panasonic Pages: 73

Brand: Panasonic Pages: 12

AWE800 - COLOR CAMERA

Brand: Panasonic Pages: 2

Brand: Abode Pages: 5

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

Digiplex EVO DGP2-640

Brand: Paradox Pages: 24

Brand: La Crosse Technology Pages: 2

ELI-IP5-APTZ21-30X

Brand: E-line Pages: 38

Brand: EVE Pages: 43

Air Live FE-200CU

Brand: Ovislink Pages: 3

MAXXUM 2XI - PART 1

Brand: Minolta Pages: 24

Brand: Zumimall Pages: 24

Brand: Uniden Pages: 66

Brand: Malmbergs Pages: 6

Brand: ADT Pages: 14

The Protector NW308

Brand: Nationwide Industries Pages: 2

Brand: E2S Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands