manualshive.com logo in svg

Sensopart 529-11008, Manual, Page: 4 / 17

Share
Download
Sensopart 529-11008 Manual Download Page 4

RailPilot system manual

   

 

 

 

 

3 

Contents 

1

 

RailPilot FR 85 anti-collision sensor .............................................................................................................. 4

 

1.1  RailPilot FR 85 sensor technology ...................................................................................................... 5 
1.1.1  Aligning RailPilot in a conveyor system (EMS) ................................................................................... 5 
1.2  RailPilot versions ................................................................................................................................. 6 
1.2.1  FR 85-2 ILLG – POL5 ......................................................................................................................... 7 
1.2.2  FR 85-2 ILLG – S1L5 .......................................................................................................................... 8 
1.3  Example of change-over of safety ranges .......................................................................................... 9 
1.4  Installation / Mounting suggestion ....................................................................................................... 9 

2

 

Setting FR 85 with PC software .................................................................................................................. 10

 

2.1  Serial communication FR 85-2 ILLG-S1L5 ....................................................................................... 10 
2.2  PC-Software FR85-2 ILLG protocol tester ........................................................................................ 11 
2.3  FR 85-2 ILLG – POL5 ....................................................................................................................... 12 
2.4  Programming with ProgSensor ......................................................................................................... 13 
2.4.1  System requirements ........................................................................................................................ 13 
2.4.2  Installation ......................................................................................................................................... 13 
2.4.3  Explanation ProgSensor ................................................................................................................... 14 
2.4.4  Symbols button bar ........................................................................................................................... 15 
2.4.5  Procedure for programming FR 85-2 ILLG with settings from another sensor ................................. 15 

3

 

Order informationen .................................................................................................................................... 15

 

3.1  Accessories ....................................................................................................................................... 15 

 

 

Summary of Contents for 529-11008


















Reviews:

No comments