Sensata dimensions 12NP18 Owner'S Manual Download Page 46

Page 46

12NP Manual

LIMITED WARRANTY TERMS & CONDITIONS 

SHIPPING TERMS: 

 F.O.B. St. Paul Minnesota. Freight prepaid and billed, subject to prior credit approval.

MINIMUM ORDER: 

 $50.00 Net Price

LOSS OR DAMAGE: 

Loss or damage in transit are the responsibility of  the carrier. Any claim should be filed with the 

delivering transport company. Invoice, Bill of  Lading and Delivery receipt with damage noted therein must accompany any 

claims for freight damage. Claims for shortage and lost shipments must be made in writing to Sensata Technologies within 10 

days of  date of  shipment. Claims not reported within this time frame will not be honored.

PRICES:

 Prices are subject to change without notice. All orders are subject to acceptance at the factory. We reserve the right 

to invoice prices in effect at time of shipment.

TERMS: 

Net 30 days with approved credit, credit card or C.O.D.

RETURN GOODS POLICY:

• 

No returned materials will be accepted without an accompanying Returned Materials Authorization Number (RMA) from 

the factory.

• 

Credit will be issued for returned goods to the original purchaser within 60 days of  purchase, provided the inverter is 

returned to Sensata unused and not mounted. The amount of  credit will be issued at Sensata’s discretion based on the 

condition of  the product.

• 

Customer must be in good standing with Sensata Technologies.

• 

Inverters that are discontinued, high-voltage (over 24 VDC), special-order or reconditioned are excluded and will not be 

eligible for credit. Non-inverter items such as cable assemblies, fuses and fuse holders, will not be eligible for credit

• 

Support components supplied by Sensata vendors will be covered under that manufacturer’s credit return policy.

• 

Customer pays return freight.

PLEASE SHIP AUTHORIZED RETURNS TO:

Sensata Technologies RMA# 

                                , 4467 White Bear Parkway, St. Paul, MN 55110. Return Freight Prepaid.

LIMITED WARRANTY:

Sensata Technologies extends the following warranty to the original purchaser of  those goods subject to the qualifications 

indicated. Sensata warrants to the original purchaser for use that the goods or any component thereof  manufactured by 

Sensata will be free from defects in workmanship from the date of  purchase for the period listed on the product label, 

provided such goods are installed, maintained and used in accordance with Sensata and the original manufacturer’s written 

instructions. Damages caused by the misuse, undue care or obvious wear through use will not be covered by this warranty.

Components not manufactured by Sensata, but used within the assembly provided by Sensata, are subject to the warranty 

period as specified by the individual manufacturer of  said component, provided such goods are installed, maintained and used 

in accordance with Sensata and the manufacturer’s written instructions.

Sensata’s sole liability and the Purchaser’s sole remedy for a failure of  goods under this limited warranty and for any and all 

claims arising out of  the purchase and use of  the goods shall be limited to the repair or replacement of  the goods that do not 

conform to this warranty.

SENSATA RETURN PROCEDURE:

To obtain repair or replacement service under the limited warranty, the purchaser must contact the factory for a Return 

Material Authorization (RMA) Number. Once obtained, send the RMA Number along with the defective part or goods to:

Sensata Technologies RMA# 

                                , 4467 White Bear Parkway, St. Paul, MN 55110. Return Freight Prepaid.

THERE ARE NO EXPRESS WARRANTIES COVERING THESE GOODS OTHER THAN AS SET FORTH ABOVE. 

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 

LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE.

SENSATA TECHNOLOGIES ASSUMES NO LIABILITY IN CONNECTION WITH THE INSTALLATION OR USE 

OF THE PRODUCT, EXCEPT AS STATED IN THIS LIMITED WARRANTY. SENSATA TECHNOLOGIES WILL IN 

NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

WARNING: LIMITATIONS ON USE:

 DIMENSIONS™ brand products are not intended for use in connection with 

Life Support Systems and for Avionic use. Sensata Technologies® makes no warranty or representation in connection with 

their products for such uses.

Summary of Contents for dimensions 12NP18

















































Reviews: