background image

Connecting the ADN-W AM antenna module to the ADN CU1 central unit

10

  

|

  

ADN-W AM

Connecting the ADN-W AM antenna module 
to the ADN CU1 central unit

Use a system cable (supplied with the ADN-W AM; the maximum
cable length allowed is 50 m) to connect the 

PORT II

socket

 or

PORT I

socket

 of the ADN CU1 central unit to the input

socket

 of the antenna module.

To optionally combine the antenna module with wired conference
units, connect the antenna module just like a wired conference unit:

Use a system cable to connect the output socket

 of the

antenna module to the 

IN

  socket  of  an  ADN  D1  or  ADN C1  wired

conference unit.

Or:

Use a system cable to connect the 

OUT

 socket of an ADN D1 or

ADN C1 wired conference unit to the input socket 

 

 of the

antenna module.

If the power supplied to the antenna module via the system
cable is not sufficient (the antenna module does not switch on),
you have to power the antenna module using the NT 12-50C
power supply (see page 6).

Optionally, you can also connect the antenna module to the

PORT

 sockets of an ADN PS power supply. It does not matter if

you are using a string or ring topology. The antenna module is
connected just like a conference unit to the cable string or cable
ring.

8

9

4

PORT II     PORT I

ADN CU1

IN –– AUDIO –– OUT

PORT II     PORT I

100-240V~

50/60Hz  240W

2x 52.8V

1.75A

8

9

ADN-W AM

4

3

3

4

Summary of Contents for ADN-W AM



















Reviews: