background image

  FCC STATEMENT FOR USERS 

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 
(1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may 
cause undesired operation. 
 

SECTION 15.21 

The user’s manual or instruction manual for an intentional or unintentional radiator 
shall caution the user that changes or modifications not expressly approved by the 
party responsible for compliance could void the user's authority to operate the 
equipment. In cases where the manual is provided only in a form other than paper, 
such as on a computer disk or over the Internet, the information required by this 
section may be included in the manual in that alternative form, provided the user can 
reasonably be expected to have the capability to access information in that form. 
 

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT, SECTION 
15.105(b) 

This equipment has been tested and found to comply with the limits for a class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generate, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no  guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

• Reorient or relocate the receiving antenna.

 

• Increase the separation between the equipment and receiver.

 

• Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

• Consult the dealer or an experienced radio/TV technician for help.

 

 

RF RADIATION EXPOSURE WARNING 

This equipment must be installed and operated in accordance with provided 
instructions and the antenna(s) used for this transmitter must be installed to provide 
a separation distance of at least 20 cm from all persons and must not be co-located 
or operated in conjunction with any other antenna or transmitter. End-users and 
installers must be provided with antenna installation instructions and transmitter 
operating conditions to satisfy RF exposure compliance.

 

Summary of Contents for element Z01-hub





















Reviews: