background image

ENGLISH 1/8

MI003074-E

This document is property   of SENECA srl. Duplication and reprodution are forbidden, if not     authorized. 
Contents of the present documentation refers to products and technologies described in it. All technical data 
contained in the document may be modified without prior notice Content of this documentation is subject to 
periodical revision.

SENECA s.r.l.

Via Austria, 26 – 35127 – PADOVA – ITALY
Tel.  +39.049.8705355 - 8705359  -  Fax +39.049.8706287
For manuals and configuration software, please see www.seneca.it

Contents:

- General Specifications
- Technical Specifications
- Installation Rules
- Electrical connections
- Modbus connection rules
- DIP-switches settings
- Digital inputs
- Leds Signallings
- Factory Settings

Contents:

- General specifications
- Technical features
- Functioning
- Rogowski’s coil
- Electrical quantities
- Electrical connections
- LEDs signallings
- Serial interface
- Case and screw terminal numbers
- Front panel
- Display programming

Installation

Manual

Installation

Manual

Installation

Manual

Installation

Manual

S203RC-D

S203RC-D

Advanced Three-phase Network Analyzer

with display for Rogowski’s sensors

Serie S - Analizzatori di rete

EN

EN

SENECA

S

Summary of Contents for S Series









Reviews: