Senci SC 8000D, User Manual, Page: 63 / 68

CONNECTING WIRE
When supplying power some far from generator, connecting wire will be applied. The dimensions of the wire
used must conform to the requirements of the cross section and length, in order to keep the voltage drop
within a very small value between electricity terminal and supply terminal.
！
NOTICE: USE A SMALL SIZE
DIMENSION WIRE MAY CAUSE DIVICE DAMAGE.
AC APPLICATION
(1) Check the three in one meter display to make sure the current and voltage in allowed range, then loading can be added. (2) Each
loading must be connected on generator in order: first connecting larger loading, then smaller loading; first connecting inductive
loading, then resistive loading. If order is reversed and cause generator’s speed decline sharply, loading must be disconnect
immediately. (3) The balance of the three-phase generator load: When a single phase loading connected on a three phase generator,
each phase power can not exceed 1/3 of the generating total power, each phase’s current D-value must be less than 20% of the rated
current. If the circuit overload let switch trip for AC circuits, please reduce circuit loading. If the voltage in three in one meter shows too
high or too low, shut down the generator to check the reason and sweep the trouble, then restart.
DC APPLICATION
DC binding post provides power source: DC12V 8.3A
，
red binding post is “+” pole of power source; black binding
post is “-“ pole of power source. The power source can be used in 12V DC load, as well as can be used in charge
battery. (1) When charge generator battery by DC output which connected to the generator by wire, must
disconnect the wire “-“ pole which connected to the generator. (2) Connect the battery “+” pole, “-“ pole
separately with generator DC “+” pole and “-“ pole by charging wire. REMARK: DC LOAD CURRENT CAN NOT
EXCEED 8 A, WHEN CHARGE IN LARGE CAPACITY BATTERY, THE FUSE OF DC SOURCE CAN BURN OUT EASILY
DUE TO BIG CURRENT. WARNING: DO NOT REVERSE THE CHARGING WIRE’S POSITIVE POLE AND NEGATIVE
POLE. ONCE REVERSED, CAN CAUSE A BAD DAMAGE IN GENERATOR AND STORAGE BATTERY. DO NOT LET
THE POSITIVE POLE CONNECT WITH NEGTIVE POLE, OTHERWISE CAN CAUSE SHORT CIRCUIT IN BATTERY.
！
DANGER: THE BATTERY CHARGING CAN PRODUCE FLAMMABLE HYDROGEN GAS, KEEP AWAY FROM SPARKS,
FLAMES AND SMOKE WHEN CHARGING. IN ORDER TO AVOID SPARKS NEARBY, CONNECT THE STORAGE
BATTERY FIRST, AND THEN CONNECTED TO THE GENERATOR,.WHEN DISCONNECTED, FIRST DISCONNECTED
THE GENERATOR SIDE. CHARGE BATTERY IN A WELL VENTILATED PLACE. 6.6 SINGLE THREE PHASE
OPERATION Determine the load type before using single phase or three phase. Use the single/three phase
switch on the panel for selection and judge the voltage and current by three in one meter.
WARNING: THE ELECTRICAL LOAD MUST BE DISCONNECTED WHEN USING SINGLE/ THREE PHASE SWITCH
STOP
Turn the starting switch to "OFF" position, disconnect all the loadings in generator, letting the generator running with no-loading for 3
minutes.
！
NOTICE: Do not stop generator suddenly because it may cause the generator’s temperature rise abnormality, which will stuck
nozzle and damage the generator. The following steps should be take when need stop the generator: (1)Turn the speed handle to “OFF”
position; (2)Turn starting key to “OFF” position; (3) After generator stopped, turn the fuel switch to “OFF” position. (4) Pull out recoil
handle slowly until feels resistance, pull back the handle slowl y
！
NOTICE: THE LAST STEP CAN PREVENT IMPURITY INTO THE CYLINDER
TO AVOID CYLINDER LINER RUSTING
！
NOTICE: WHEN THE SPEED HANDLE LOCATE IN “STOP” POSITION AND THE GENERATOR IS STILL
RUNNING, TURN THE FUEL SWICH TO “OFF” POSITION OR LOOSEN HIGH PRESSURE OIL PIPE BOLT.NO NEED TO USE REDUCING HANDLE.
Italia Star Com Due S.R.L.
www.italiastar.ro
info@italiastar.ro
004/021.433.03.27
63