Seiko Astron 3X22 Complete User Manual Download

Page: 14 / 50

Check the charging status

Push and

release

Button B

When Button B is pushed and released, the seconds hand moves, allowing you to check the energy level.
We recommend that you check the “energy level” on a regular basis to ensure that the watch does not do into a low energy state.

* GPS signal reception requires a lot of energy. Keep in mind to regularly charge the watch by expose to light.→ About charging

P. 14

Reception is allowed

Seconds hand display

Charging status

Solution

full

Reception is allowed.

Use the watch as it is.

→

P. 15

middle

Reception is allowed, but keep in mind to charge

the watch.

→

P. 15

Reception is not allowed

Seconds hand display

Charging status

Solution

low

The watch is unable

to receive GPS

signals, but has

energy to operate.

To enable reception, charge the watch until the

energy level is at least “middle”.
→ About charging

P. 14

The movement of the

seconds hand

Charging status

Solution

2-second

interval

movement

The energy level is in a very “low”

state.
* If the energy depletion

forewarning function is

activated, the “charging status”

cannot be displayed.

To keep the watch operating and also enable

reception, continue charging the watch until the

energy level is at least “middle”.
→ About charging

P. 14

→ 2-second interval movement/5-second interval

movement are brought about

P. 28

5-second

interval

movement

BEFORE USE

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands

Seiko Astron 3X22, Complete User Manual

Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands