Seiko Astron 3X22 Complete User Manual Download

Page: 16 / 50

•

When the region or

time difference

(time zone) where

the watch is used

has changed

•

To set only the

time

1. Check the place where GPS signals can be

easily received

→ Place where GPS signals can be easily received/Place

where GPS signals cannot be received

P. 16

Place where GPS signals can be

easily received

Outdoors under an open sky with good

visibility

Place where GPS signals cannot be

received

Example: Within a subway station

2. Set the time zone and set the time and date

< Setting by GPS signal reception >

•

Receive GPS signals, set

the time zone and set the

time and date

•

If DST (daylight saving time

or “summer time”) is in effect,

set the time difference

manually

→ How to adjust the time zone

P. 20

→ How to perform manual time

difference setting (selection)

P. 23

Set only the time

→ How to manually adjust the time

P. 22

< Manual setting >

Confirm time and date display

Incorrect by increments of

hours

→ How to perform manual time difference

setting (selection)

P. 23

Time is nearly correct

→ How to manually set the time

P. 39

Basic operation flow

BASIC OPERATION (HOW TO SET THE TIME/HOW TO RECEIVE GPS SIGNALS, ETC.)

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands

Seiko Astron 3X22, Complete User Manual

Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands