Seiki ULA-25GSC Instruction Manual Download Page 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 (1)Change over the dip switch on the control panel. 

When you change the side to the left-hand,  
adjust the side changeover to "Left".  

(2)Take off the screws with which the brake case and 

the right-left fixing plate are mounted. 

(3)Change the direction of the right-left fixing plate. 

In case of changing over to the left-hand side,  
see to it that the side display mark (round mark) 
comes to the left side display mark side.  

(4)Mount the right-left fixing plate onto the brake case 

 with screws. 

(5)Loosen 4 screws to turn brake housing. 

When turning the brake housing, position it in order  
to enable the short-link handchain to be hauled downward. 

 Press brake release lever when turning brake housing, and it makes work easier. 

(6)Screw the brake housing in a desired position to fix. 

At this moment, tighten it up so that there be no gap between brake housing and motor when pressing 
brake release lever. 
And also tighten up 2 fixing screws along each diagonal line in order. 

 

   The operator is shipped in the exclusive installation for the right-hand side or the left-hand side. 

If you want the changeover on the installation side between the right-hand and the left-hand, follow 
the procedures described below. 
After making checks on the right-hand and the left-hand at the installation site, you should make 
changeover between opposite sides in a proper manner. 

 

Changeover between Right-hand and Left-hand Side Settings

 

Prior to installing the operator onto the bracket, you should reassemble the  
right-left fixing plate.  
・If you detach the right-left fixing plate from the brake case in a state of load 
 being applied, the brake does not work, and so the shutter may sometimes fall with 
 its gravity or you may undergo injury with the fixing plate coming off. 

WARNING 

P5 

Right-hand side

 

Left-hand side

 

Summary of Contents for ULA-25GSC






















Reviews: