background image

 

Release Version 1.8 

7. Transmission Distance Depending on Coaxial Cable Type 

(unit: m)

 

Power 

Watt 

Loop Resistance   

by PoE 

ECX 5C-2V 

(High) 

ECX 5C-2V 

(Normal) 

RG-6 

(High) 

RG-6 

(Normal) 

RG-6 

(Low) 

3.0W 

70.0  Ω 

1,650 

930 

1,680 

930 

400 

6.0W 

48.0  Ω 

1,130 

640 

1,150 

640 

270 

9.0W 

36.0  Ω 

840 

480 

860 

480 

200 

12.0W 

30.0  Ω 

700 

400 

720 

400 

170 

15.0W 

24.0  Ω 

560 

320 

570 

320 

130 

18.0W 

21.0  Ω 

490 

280 

500 

280 

120 

21.0W 

18.0  Ω 

420 

240 

430 

240 

100 

24.0W 

16.0  Ω 

370 

210 

380 

210 

90 

27.0W 

13.5  Ω 

310 

180 

320 

180 

70 

30.0W 

10.5  Ω 

240 

140 

250 

140 

60 

(Cable Loop resistance: Coaxial cable)

 

※  The transmission distance may vary depending on the coaxial cable and connector construction quality. 
※  There may be a difference between 20~30% of the available power values in above table depending on 

the power status of camera. 

※  The transmission distance may vary depending on the specification of camera and NVR. 
※  In case of using PoE function of the Transmitter, the transmission distance may vary depending on the 

type of camera. Especially, use exclusive adaptor for cameras with high power consumption such as IP 
PTZ cameras and the cameras with many IR LEDs.   

In addition, the length of NETWORK CABLE between camera and Transmitter is recommended to be 
within 1m. 

※  In case of supplying power to Receiver by PoE Hub, the length of NETWORK CABLE is recommended to 

be within 1m. 

 

8. Installation Precautions 

※  Use exclusive power adapter separately for each product. It is not recommended to use single adapter 

for supplying power to several products. 

※  It is not recommended to place products in close or tie each other. 
※  When installing this product, make sure to perform Pairing by pressing Function Key for 3~5 seconds.   
※  When Pairing multiple products at the same area, make sure to supply power ONLY to the product 

performing Pairing.   

※  After pairing is completed, turn the power off and perform another product’s Pairing in the same way. 
※  In case of using camera’s power adapter, turn PoE OFF from Transmitter. 
※  Perform Pairing again in case of video abnormality or disconnection during use. 

 

※  It is not recommended to connect adaptor to DC jack when powering the Receiver by PoE.   
※  When installing the product by supplying power by PoE, it is recommended to check the video first and 

connect the ground of camera.   

※  When using a surge protector, the cable distance between camera and Receiver is recommended to be 

within 50M.   

Summary of Contents for SC-IPR3001E

















Reviews: