background image

SafeLogic Xtreme Installation and Operation Instructions   

Doc. No. XU-EC1501A-X151123 

 

SecuRam Systems Inc.         

  

Page 12 

 

 

 

Step  3:    Test  the  operation  of  the  mechanical  combination.  Refer  to  “Mechanical  Lock  Operating 

Instructions”.  

Step 4:  After above test, turn the SpinDial until the number “00” aligns with the twelve o’clock  

position of the ring. (Fig. 7) and close the SpinDial release. (Fig. 8)  

  

8.0  Electronic Lock Operating Instructions  

The SafeLogic Xtreme comes with the user code set to the factory default of 1-2-3-4-5-6.  

8.1  To Open the Lock with a Code Step 

1:  Press 1-2-3-4-5-6.  

Step 2:  The lock opens   

Step 3:  Then relocks after 6 seconds.   

  

8.2  To Change the Default User Code  

Step 1:  Enter 0-0-0-0-0-0  

Step 2:  The lock will beep once indicating that it is ready for programming Step 

3:  Enter the existing 6 digit code.  The Lock will beep once.  

Step 4:  Now enter the new 6 digit code.  The lock will beep once.  

Step 5:  Now repeat the new 6 digit code.  The lock will beep once indicating that the change  

code process is complete.    

Step 6:  Now enter the new code to test the lock.  

   If the lock does not open using the new code, repeat the change code process again.  

  

  

9.0  Mechanical Lock Operating Instructions  

The mechanical combination of SafeLogic Xtreme preset to 50-50-50.    

  

Summary of Contents for SafeLogic Xtreme


















Reviews: