background image

 

 

 

 

 

 

 

 

 

 

 

Figure 6: 

Solve the mounting base from the housing by turning it counterclockwise. 

 

3.  After the successful replacement of the battery, mount the housing of the smoke alarm back to 

the mounting base. To fix this, rotate the housing clockwise (

see Figure 6

). 

 

4.  Thereafter, please check the smoke alarm detector by pressing the test button for about 5 

seconds on its function. The smoke alarm detector should sound 3 times shortly.  If the smoke 
alarm detector give no beep of itself, is here eventually a malfunction or the battery has been 
inserted incorrectly, please note + and - pole! 

Note: 

Please check the smoke alarm detector after replacing the battery always on its function! 

 

7.  Reasons for triggering a false alarm 

 

The following may be causes of a false alarm: 

 

Water and kitchen steam 

 

high air humidity 

 

dust 

 

Strong drafts etc. 

 

Usually the smoke of cigarettes does not trigger the alarm. If the alarm still be triggered, please 
make sure that not a fire has activated the smoke alarm detector! If no fire is detected in one of 
the rooms, you can deactivate the alarm of the smoke alarm detector by removing the batteries. 
Then insert the batteries again and test the smoke alarm detector again on its function using by 
the test button (

see chapter 4.1). 

 

Summary of Contents for GS506G












Reviews: