background image

Table of contents 

 

Table of contents...............................................................................................................……….. 2 

Required radio, motor and battery.............................................................................................…. 3 

Additional required items, tools and adhesives.............................................................................. 3 

Warning.......................................................................................................................................... 3 

Before starting assembly ...........................................................................................................…  4 

Using the manual........................................................................................................................... 4 

Warranty information…................................................................................................................. 4 

Section 1 – wing fillet installation….............................................................................................. 5 

Section 2 – ailerons installation……….......................................................................................... 7 

Section 3 – aileron servo & control horn installation…............................................................…. 8 

Section 4 – elevator installation….................................................................................................. 11 

Section 5 – elevator servo installation…….................................................................................... 14 

Section 6 – tail wheel & rudder installation ………....................................................................... 16 

Section 7 – rudder servo installation……......................................…........................................…. 20 

Section 8 – landing gear & wheel installation................................................................................ 23 

Section 9 – electric motor & cowl installation…….......……......................................................... 26 

Section 10 – glow engine & cowl installation.......................................................................……. 30 

Section 11 – final radio installation ……………........................................................................... 39 

Section 12 – hatch & cockpit  installation….................................................................................. 40 

Wing installation……..................................................................................................................... 42 

Control throws…………………….......................................................................................……. 42 

Mixing............................................................................................................................................. 42 

Rates and expos..........................................................................................................................… 43 

Recommended CG......................................................................................................................… 43 

Pre-flight…................................................................................................................................….. 43 

Range test your radio..................................................................................................................…. 43 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for KatanaS 120 ARF












































Reviews: