background image

For the repair or replacement parts you need

Call 7 am - 7 pm, 7 days a week

1-800-366-PART

(1-800-366-7278)

For in-home major brand repair service

Call 24 hours a day, 7 days a week

1-800-4-REPAIR

(1-800-473-7247)

For the location of a 

Sears Repair Service Center in your area

Call 24 hours a day, 7 days a week

1-800-488-1222

For information on purchasing a Sears

Maintenance Agreement or to inquire 

about an existing Agreement

call 9 am - 5 pm, Monday-Saturday

1-800-827-6655

MAINTENANCE

AG

REEMENT

America's Repair Specialists

REPAIR SERVICES

America's Repair Specialists

REPAIR SERVICES

America's Repair Specialists

REPAIR SERVICES

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

OWNER’S 

MANUAL

MODEL NO.

390.250284

The model number of
your Shallow Well Jet
Pump will be found on a
plate attached to the
pump discharge 
connection. 

When requesting service
or ordering parts, always
give the following 
information:
• Product Type
• Model Number
• Part Number
• Part Description

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

HYDROGLASS

®

SHALLOW WELL 
JET PUMP

®

Summary of Contents for CRAFTSMAN HYDROGLASS 390.250284













Reviews: