205L 12V & 230V ELECTRIC DRUM PUMP
MODEL NO:
TP6818.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
DO NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING!
Ensure Health & Safety, government and local authority regulations relating to the transfer of diesel are adhered to when
using
this equipment. Familiarise yourself with the application, limitations and specific hazards peculiar to the pump.
WARNING!
Disconnect pump from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain pump in good condition (use authorised service agent). Drain before dismantling.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Ensure the transfer area is free of clutter and has adequate lighting.
9
Keep children and unauthorised persons away from the working area.
9
Replace/repair damaged parts. Use genuine parts. Unauthorised parts are dangerous and will invalidate warranty.
8
DO NOT
use the pump without the delivery nozzle attached.
8
DO NOT
start or stop the pump by switching on or off at the mains power supply.
8
DO NOT
operate the unit with wet hands. We recommend the use of gloves and goggles.
9
It is installer’s responsibility to ensure all supply pipes, fixtures and fittings are adequate for the safe flow of diesel fuel.
8
DO NOT
use this pump for transferring the following liquids; Aceton, Benzen, Cresol, Ethyl, Phenol, Methyl ethyl, Concentrated
caustic soda liquid, Nitric acid, Hydrochloric acid, Sulfuric-acid, thinner or solvents, Etc.
8
DO NOT
use for concentrated acids. Only use on applicable liquids written on the specifications. Make sure to use the pump on
even surface.
8
DO NOT
use when the cable and plug is damaged or if plug is loose on outlet.
9
Keep the power supply adapter out of direct sunlight, water vapour, soft coal, dust, and damp air etc.
8
DO NOT
touch and operate any plug or power supply units with wet hands.
9
Make sure the pump is tightly secured to the drum (tank) before turning the pump on.
8
DO NOT
refuel directly while the vehicle or equipment is turned on.
8
DO NOT
leave the pump unattended.
Recommended fuse rating
5 Amp
T
P6818.V2 Issue 1 07/09/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
