note:
Children aged from 3 years and less than 8 years shall only switch on/off the heater provided that it has been placed or installed
in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in
a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
2. IntroductIon
A totally dry heat, no condensation, no gas, no fumes and no smell. Reaches maximum heat output within seconds of being turned on. Highly
polished aluminium reflector for maximum heat efficiency. Adjusts horizontally through 25° while mounted. Three settings, controlled by pull
cord, allowing unit to be on full, half or low power. Ideal for industrial or domestic applications. Suitable for indoor and outdoor use, if weather
protected (Heater is IP24 rated).
3. specIfIcatIon
Model no: ...............................................................IFSH2003
Power: .........................................................................
2000W
Supply: ................................................................. 230V - 13A
S
ize (W x D x H):
....................................485 x 170 x 250mm
M
in/max height:
...............................................
1530/1850mm
4. asseMblY
refer to fig.1
4.1.
Insert the welded plate end of section 9 into the base 10 and secure using washer 11 and
screw 12.
4.2.
Slide section 8 onto section 9 and secure using screw 14. Slide section 5 upwards from
inside of section 7, turn lock screw 6 clockwise to secure and then slide section 7 onto
section 8 and secure using screw 14.
4.3.
Insert the end of section 5 into the base of the heater (1) and secure with screw 13.
4.4.
Align Clip 3 to the holes in sections 7 and 9 and secure with screw 4.
5. operatIon
WarnInG!
ensure you read, understand and apply the safety instructions in
section 1 before using the heater.
5.1.
ensure the heater is at least 1m from any object, 300m from the ceiling. The heater can
be tilted from 0° to 25°, set it to the required angle before switching the heater on.
5.2.
Plug in the heater and switch it on using the pull chord on the heater head.
5.3.
The heater will start on the low setting, each pull of the chord will cycle the heater onto the
medium setting, high setting and then back to off. (fig.1B)
5.4.
When the heater is no longer required, switch to the off position and unplug the unit.
5.5.
Make sure the heater plug is disconnected from the mains supply before any cleaning is
attempted. Also allow the heater to cool completely.
8
do not
use harsh abrasive cleaners to clean the heater.
8
do not
touch the glass elements with fingers as this may damage the tube.
5.6.
Clean the exterior with a soft damp cloth with some mild detergent.
5.7.
To replace any of the elements, contact your authorised Sealey stockist.
5.8.
The heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted
beyond 25° either forwards or backwards. This prevents fire in the event of the unit being
knocked over. If the unit does not turn on again when returned to the vertical, tip it
approximately 25° in the opposite direction until you hear the internal switch operate. As
the heater switches on return it to the vertical position.
sealey Group, Kempson Way, suffolk business park, bury st edmunds, suffolk. Ip32 7ar
01284 757500
01284 703534
www.sealey.co.uk
note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important
: no liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Weee reGulatIons
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
enVIronMent protectIon
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
fig.1
I
FSH2003 | Issue:5 (ERP) 23/08/18
Original Language Version
© Jack Sealey limited
