background image

INFRARED  VENT-FREE

PROPANE/LP GAS

SPACE  H E AT E R

HR06ML-1   HR10ML-1   HR10TL-1

        WA R N I N G :    

I m p r o p e r       i n s t a l l a t i o n ,

adjustment,  alteration,  service    or    mainte-
nance can  cause  injury  or  property  damage.
Refer  to  this  manual  for  correct  installation  and
operational  procedures.  For  assistance  or
additional  information  consult  a  qualified
installer,  service  agency,  or   gas  supplier.

This  appliance  may  be  installed  in  an  aftermar-
ket*    permanently    located,  manufactured
(mobile) home, where  not  prohibited  by  local
codes.
This appliance  is  only  for  use  with  the  type  of
gas    indicated    on    the    rating    plate.  This
appliance  is  not  convertible  for  use  with  other
gases.

*Aftermarket: Completion  of  sale, not  for  purpose  of
resale,  from  the  manufacturer.

Do  not  store,  or  use  gasoline  or  other  flammable
vapors  and  liquids  in  the  vicinity  of  this  or  any
other  appliance.

WHAT  TO  DO  IF  YOU  SMELL  GAS

Do  not  try  to  light  any  appliance.

Do   not   touch   any   electrical   switch;  do  not

       use  any  phone  in   your  building.

Immediately   call   your  gas  supplier  from  a

       neighbor’s   phone.   Follow   the   gas  supplier’s
       instructions.

If   you   cannot  reach  your  gas  supplier, call

       the  fire  department.
Installation  and  service  must  be  performed  by  a
q u a l i f i e d     i n s t a l l e r ,   s e r v i c e     a g e n c y     o r     g a s
supplier.

Table  of  Contents

Important Safety Information.................................2

Product  Features.....................................................3

Proper Ventilation & Fresh Air..............................4

Installation................................................................6

Operating Your Heater............................................10

Cleaning & Maintenance.......................................13

Trouble  Shooting...................................................14

Specifications..........................................................17

Parts List..................................................................19

Warranty Information.............................................24

      WARNING: 

 If  the  information  in this

manual  is  not  followed  exactly, a   f i r e   o r
e x p l o s i o n     m a y     r e s u l t  causing  property
damage,  personal injury,  or  loss  of  life.

    WARNING:  

 This  is  an  unvented gas-

fired heater.  It  uses  air  (oxygen) f r o m     t h e
r o o m     i n     w h i c h     i t     i s  installed.  Provi-
sions  for  adequate combustion  and  ventila-
tion  air  must  b e   p r o v i d e d .   R e f e r   t o   A i r
F o r  Combustion  and  Ventilation section on
page  4  of  this  manual.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM
HEATERS
Water  vapor  is  a  by-product  of  gas  combustion.An
unvented room heater productes approximately one (1)
ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) of
gas input per hour. Refer to page 3.

Installer: Please leave these instructions with the
consumer.

Consumer: Please retain these instructions for
future use.

OWNER

S OPERATION AND INSTALLATION MANUAL

A Division of Empire Comfort Systems,Inc.

                                   918 Freeburg Avenue

Phone : 618-233-7420 or 1-800-851-3153

Fax : 618-233-7097 or 1-800-443-8648

www.hearthrite.com

Belleville,IL 62220

Summary of Contents for HR06ML-1

























Reviews: