NOTE:
Excessive pressure on the machine does not result in higher working efficiency. It increases wear on the internal mechanics and can
damage the polisher/sander and the item being worked.
4.1.
Set the speed using Speed Control dial (fig.1) in accordance to the polish and the material being worked. Read the polish
manufacturer’s instructions for correct settings. Speed settings are shown below.
4.2.
Use the relevant pad required for the job - sanding and polishing pads not included. See Sealey website for more details
5. MAINTENANCE
WARNING!
Remove battery from tool before performing any maintenance or making adjustments.
5.1.
Keep the ventilation slots of the machine clean to prevent overheating of the motor.
5.2.
Regularly remove dust / debris with a soft bristled brush.
8
DO NOT
use solvents. Clean with a soft damp cloth.
DO NOT
use compressed air (risk of ejection).
5.3.
Tool does not require any special maintenance (it is permanently lubricated inside). Professional repair only, contact authorised
service centre.
5.4.
STORAGE:
Store in a child free,dry location.
WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 10.524 m/s²
Uncertainty value (k):
1.5
m/s²
Please note that the application of the tool to a sole specialist task may produce a
different average vibration emission. We recommend that a specific evaluation of the vibration emission is conducted prior to
commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can
be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm
and dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please refer to
the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
REGISTER YOUR
PURCHASE HERE
C
P108VSPBO Issue 1 06/06/22
Original Language Version
© Jack Sealey Limited
Setting
S
peed (rpm) (approximate)
1
2500
2
3000
3
3500
4
4000
5
4500
6
5000
