background image

PLEASE READ AND FOLLOW ALL WARNINGS

Read Operating Instructions

Always become familiar with all the
instructions and warnings before operating
any power tool.

Always Wear Approved
Eye Protection

Impact resistant eye protection should
meet or exceed the standards as set forth
in the United States ANSI Z87.1,
Occupational and Educational Eye and
Face Protection. Look for the marking
Z87.1 on your eye protection to insure that
it is an approved style. For further
information, ANSI Z87.1, Occupational and
Educational Eye and Face Protection, is
available from the American National
Standards Institute, Inc., 11 West 42nd

Street, New York, NY 10036

.

Hearing Protection is
Recommended

H

earing protection should be used when the

noise level exposure equals or exceeds an
8 hour time-weighted average sound level
of 85 dBA. Process noise, reflective
surfaces, other tools being operated
nearby, all add to the noise level present in
your work area. If you are unable to
determine your noise level exposure, we
recommend the use of hearing protection.

Avoid Prolonged Exposure to
Vibration

PnuematicTools can vibrate during use.
Prolonged exposure to vibration or very
repetitive hand and arm movements, can
cause injury.  Stop using any tool if
discomfort, tingling feeling or pain occurs.
You should consult your physician before
resuming use of the tool.

90 PSIG Maximum

This tool is designed to operate at an air
pressure of 90 pounds per square inch
gauge pressure (90 PSIG) maximum, at the
tool. Use of higher air pressure can, and
may cause injury.  Also, the use of higher
air pressure places the internal components
under loads and stresses they were not

designed for, causing premature

Universal Tool

A Division of Florida Pneumatic Manufacturing Corporation

851 Jupiter Park Lane, Jupiter, Florida 33458

Toll Free 1-800-327-9403

Read these instructions carefully before attempting to install, operate or
service this Florida Pneumatic product.  Failure to comply with the instruc-
tions could result in personal injury and/or property damage!  Retain these
instructions for future reference.

Safety Instructions

The following instructions are furnished as
general guidelines for use of your pneu-
matic tool.  They cannot comprehensively
cover all possible or conceivable uses of
the subject tool.  For additional information
on the safe use of air tools, we advise you
to obtain a copy of ANSI B186.1 Safety
Code for Portable Air Tools, available from
the following source:

American National Standards

                Institute, Inc.

11 West 42nd Street
New York, NY 10036.

The use of the word “shall” in the following
instructions, indicates that adherence to
the particular requirement is necessary to
conform to ANSI B186.1.

Tool Application and Usage

Pneumatic tools shall be used only for the
purposes intended in their design and
within the capacity for which they were

FPMC

WARNING:

Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or reproductive harm. Some examples of
these chemicals are:

Lead from lead-based paints

Crystalline silica from bricks, cement and
other masonry products

Arsenic and chromium from chemically
treated lumber

Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-
ventilated area and work with approved safety
equipment such as those dust masks that are
specially designed to filter out microscopic
particles.

MODEL NO.  UT8718 / UT8718K

DESCRIPTION

UT8718 (Shown with Kit)

intended and rated.  It shall be the tool owner’s
and/or employer’s responsibility to instruct
each operator in the safe use of the tool.
Tools shall not be used without guards and
safety devices as furnished by the manufac-
turer.  Where an air tool is modified or altered,
the modifier shall provide the safeguards to
enable it to be safely used in the operations
intended and to comply with any applicable
provisions as contained in ANSI B186.1.

Tool Installation

Pressure regulators shall be used to limit air
pressure to the rated pressure where the
supply pressure exceeds the tool’s rated
pressure.  Air hoses and lines shall be
relieved of compressed air before being
disconnected or disjointed, unless there is
automatic valve closing protection at the joint
being separated.  Synthetic lubricants which
can cause deterioration of elastomer seals
shall not be used in air systems of air tools.

T

T

T

T

Tool Maintenance

ool Maintenance

ool Maintenance

ool Maintenance

ool Maintenance

It shall be the tool owner.s and/or
employer.s responsibility to assure that
tools are maintained in a safe operating
condition. Tool maintenance and repair
shall be performed by authorized,
trained, competent personnel. Tools
shall be disconnected from their
compressed air supply before repairs
are attempted. Repairs shall be
consistent with the manufacturer.s
recommended procedures.
Tool, hoses and fittings shall be
replaced if unsuitable for safe operation.
It shall be the tool owner.s and/or
employer.s responsibility to keep
required rating markings and warnings
on the tool in legible condition.

.

Description

Description

Description

Description

Description

Universal Tool Multi-Angle Belt Sander is designed fro hard-to-reach corners,
contours, and hard-to-finish surfaces. Used to sand, grind, and finish aluminum,
steel, cast iron, plywood, plastic and stone. 

Please note : Multi-Angle Belt

Sanders are not designed for sanding directly on the front roller.

Reviews: