3. speCiFiCation
model no: ...................................................................bt2015
rated battery voltage: ...................................................6/12V
charging system capacity: .......................................12/24V**
rating systems: ................................din, en, iec, Jis, sAe
test ranges:
.................................................................. 40-2830 ccA* en
................................................................. 40-3000ccA* sAe
................................................................. 30-1985 ccA* iec
................................................................. 25-1685 ccA* din
................................................................. by battery type Jis
minimum power requirement: ..........................................1.5V
Voltage range: ............................................................1.5-30V
battery: ....................................................... 6 x AA (supplied)
consumable parts: ...... bt2003.V2-01 - printing roll pack of 2
note: .........................................*ccA - cold cranking Amps,
...................................................... **24V Alternator test only
compatibility: ....................................... Windows XP, 7, 8, 10
4. preparation For test
4.1.
be sure area around battery is well ventilated while battery is being tested.
4.2.
clean battery terminals. be careful to keep corrosion from coming in contact with eyes.
4.3.
inspect the battery for cracked or broken case or cover. if battery is damaged,
do not
use tester.
4.4.
if the battery is not sealed maintenance free, add distilled water in each cell until battery acid reaches level
specified by the manufacturer. This helps purge excessive gas from cells.
do not
overfill.
4.5.
If it is necessary to remove battery from vehicle to test, always remove ground terminal from battery first.
make sure all accessories in the vehicle are off to ensure there is no arcing.
5. operation
5.1.
insertion or replaCeMent oF lead wire
Refer to fig.1
5.1.1. remove the cover on the backside bottom of the battery tester.
5.1.2. insert the connectors which contain a black-yellow pair and a yellow-red pair, in one end of the lead wire into
the sockets which can be found when the cover is removed as above. make sure the colours match between
the connectors and sockets as shown in fig.1.
5.2.
beFore testing
5.2.1.
before you test a battery in a vehicle, turn off the ignition, all accessories and loads.
5.2.2.
make sure you have put 6 x AA 1.5V batteries into the battery chamber. oxyride batteries are not recommended
because of the initial 1.7 Volt output. if the internal 1.5V batteries run out of power, the display will show
“PoWer loW”. replace those 6 x AA 1.5V batteries before starting a new test.
5.2.3.
note that nothing will be seen on the display until the tester is connected to a vehicle battery.
5.2.4.
make sure all battery terminals are clean and wire brush them if necessary. connect the red clamp to the
positive battery terminal post, then connect the black clamp to the negative battery terminal post. for the
most accurate results, clamp on the lead part of the terminal only.
5.2.5.
Attaching to the clamp or other fixture rather than directly on the terminal could result in a unstable incorrect
test result.
5.3.
PAPER LOAD Refer to fig.2
5.3.1.
open the clear cover.
5.3.2.
Place a new roll in the compartment.
5.3.3.
Pull a short length of paper from the compartment and press down the clear cover to close.
5.4.
start stop battery test
5.4.1.
Press the ◄► to select START-STOP test. There are 3 tests for selection:
stArt stoP test
bAtterY test
sYstem test
5.4.2.
Press the ◄► key to select battery type:
a) efb (enHAnced flooded)
b) AGm flAt PlAte
Press ‘ENTER’ to confirm choice.
5.4.3.
Press the ◄► key to select the battery rating:
SAE (CCA), EN, IEC or DIN. Press ‘ENTER’ to confirm choice.
Original Language Version
© Jack sealey limited
Fig.1
Fig.2
stArt stoP
XX.XXV
bAtterY tYPe
efb
select rAtinG
sAe
bt2015 | issue:1 17/10/17
