Seagull Models Laser 200 Assembly Manual Download Page 1 | Manualshive

Page: 1 / 23

background image

LASER 200

Hand-made Almost Ready to Fly R/C Model Aircraft

ASSEMBLY MANUAL

Made in Vietnam.

Kit features

•

Ready-made-minimal assembly & finishing required.

•

Ready-covered covering.

•

Comprehensive hardware pack including wheels, tank, spats,undercarriage.

•

Photo-illustrated step-by-step Assembly Manual.

SPECIFICATIONS:

WING SPAN ----------------------------------------175CM -------------------------------- 68.75 in.
WING AREA ------------------------------------------4746CM2 --------------------------735.6 Sq.in.
WEIGHT ---------------------------------------4.1 - 5KG ---------------------- 9.02lb - 11lb.
ENGINE SIZE -------------------------------------.91 - 1.20 ---------------------------- 2 stroke.
-------------------------------------1.20 - 1.50 ---------------------------- 4 stroke.
RECOMMENDED R/C --------------------------- 4 CHANNEL MINIMUM WITH 6 SERVOS.
FLYING SKILL LEVEL ----------------------------------------ADVANCED / INTERMEDIATE.
LENGTH -------------------------------------------161CM ----------------------------------63.4in.

1
2
3
...
»

Summary of Contents for Laser 200
























Reviews:

No comments

Related manuals for Laser 200

Brand: Old School Model Works Pages: 14

Brand: LAEGENDARY Pages: 32

Brand: Pinolino Pages: 12

IMAGINEXT B9774

Brand: Fisher-Price Pages: 6

Brand: marklin Pages: 32

Cathy II P-51 Mustang

Brand: AIR core Pages: 2

Brand: H-KING Pages: 9

Brand: LEGO Pages: 72

Brand: SL Model Pages: 40

Brand: Stevens AeroModel Pages: 29

Tank Car 4-axle 67230

Brand: BRAWA Pages: 4

Fordhampton Farm House

Brand: GAUGEMASTER Pages: 4

Star Wars Electronic Ask Yoda 72410

Brand: Hasbro Pages: 4

Super Mario Adventures with Peach

Brand: LEGO Pages: 24

Brand: Mega Bloks Pages: 2

Volkswagen Beetle LED Lighting Kit

Brand: LIGHT MY BRICKS Pages: 15

Brand: Gyros Pages: 14

1563W Wabash Freight Set

Brand: Lionel Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands