Seagull Models ET 6 - TEXAN Assembly Manual Download Page 1 | Manualshive

Page: 1 / 15

background image

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered covering.

•

Photo-illustrated step-by-step Assembly Manual.

Made in Vietnam.

Specifications

Wing Span ------------------------------- 62.5 in ------------------ 158.7cm.
Wing Area -----------------------------627.8 sq in ------------ 40.5 sq dm.
Weight ---------------------------------5.3 - 6.0 lbs -------2400 g - 2700g.
Length ------------------------------------ 46.6 in ------------------ 118.3cm.

Need to Complete

Speed Control: 100 - 120 amp.
Recommended Battery 4 - 5 cells. 3000 - 5000mAh Li-Po.

ASSEMBLY MANUAL

MS: X11

ET 6 - TEXAN

“Graphics and specfications
may change without notice”.

2

1
2
3
...
»

Summary of Contents for ET 6 - TEXAN
















Reviews:

No comments

Related manuals for ET 6 - TEXAN

Brand: Rage RC Pages: 16

SM-79 Sparviero Exterior

Brand: Eduard Pages: 4

Brand: Minicraft Models Pages: 4

EXTRA 330SC 60CC

Brand: AeroPlus Pages: 19

Techno Tiles TT Castle

Brand: The Learning Journey Pages: 386

Brand: Faller Pages: 8

Brand: marklin Pages: 20

Brand: Spin Master Pages: 3

Brand: Solly Systems Pages: 56

Brand: Wilhelm Schroder Pages: 4

SH-3 Sea King interior

Brand: Eduard Pages: 2

Brand: PARKZONE Pages: 88

Brand: Jamara Pages: 12

Origami 3D Ladybug 2568

Brand: Alexander Pages: 27

GAMETIME HOCKEY RINK

Brand: OYO Sports Pages: 60

National Geographic NG300 ICHTHYOSAUR

Brand: Laser Pegs Pages: 27

GIJoe Earthquake

Brand: Hasbro Pages: 4

Brand: T3 Simulations Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands