Seagull Models CURTISS P-40N WARHAWK Assembly Manual Download Page 17 | Manualshive

Page: 17 / 28

background image

WWW.SEAGULLMODELS.COM

17

3x10mm

2) Install the muffler and muffler extension

onto the engine and make the cutout in the

cowl for muffler clearance. Connect the fuel

and pressure lines to the carburetor, muffler

and fuel filler valve. Secure the cowl to fuse-

lage using the M3x10mm screws.

The propeller should not touch any

part of the spinner cone. If it does, use a

sharp modeling knife and carefully trim

away the spinner cone where the propel-

ler comes in contact with it.

INSTALLING THE SPINNER.

INSTALL ELEVATOR CONTROL HORN.

Fiberglass control horn

HINGING THE ELEVATOR.

Glue the elevator hinges in place using the

same techniques used to hing the ailerons.

«
...
15
16
17
18
19
...
»

Summary of Contents for CURTISS P-40N WARHAWK





























Reviews:

No comments

Related manuals for CURTISS P-40N WARHAWK

Brand: Jamara Pages: 20

265 ALUTWIN 2,4G

Brand: NINCOAIR Pages: 21

Triple-the-Fun Art Studio

Brand: Crayola Pages: 3

Brand: Fisher-Price Pages: 2

Lokpuffer Puff-H0

Brand: Fichtelbahn Pages: 2

ELECTRONIC SUDOKU

Brand: LEXIBOOK Pages: 19

Vac-U-Soling Lower Hull Kit

Brand: Vac-U-Boat Pages: 30

Brand: Gogen Pages: 40

Brand: E-FLITE Pages: 40

HANGAR 9 Fun Scale PT-19 PNP

Brand: Horizon Hobby Pages: 48

Brand: Jamara Pages: 8

Carole Towne GARAGE SANFORD

Brand: LF Pages: 7

Nest & Learn Animals

Brand: VTech Pages: 10

Brand: Power Wheels Pages: 32

Orc Krushinator Deffstomper Body

Brand: Tabletop Scenics Pages: 20

Brand: marklin Pages: 12

Brand: E-FLITE Pages: 20

Grab & Go Koala 5368

Brand: VTech Baby Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands